Installation; Correct Cutting Position; Starting Up; Instructions For Use - Stel THOR 103 Manual De Instrucciones

TECHNICAL
DESCRIPTION
6.0– INSTALLATION
6.1– CORRECT CUTTING POSITION
During use of the machine the operator must stand at the front so as to
prevent the fumes produced by cutting from being sucked into the
machine by the cooling fans (through the front and side ventilation
openings.
6.2– STARTING UP
The operator may start up the machine only after having read and
understood all parts of this manual. Depending on the type of cut to be
performed he must follow the work phases described below.

6.3- INSTRUCTIONS FOR USE

1- Ensure that the work environment and your clothing satisfy the safety
requirements described on PAGE 3.
2- Position the generator in a place where there is no obstacle to air
circulation.
3- Connect the THOR to a suitable power socket (an earthed socket is
obligatory).
4- Connect the compressed air pipe to the air filter on the rear panel.
-5- Ensure that there is no water in the filter. If necessary, empty the
filter.
For the instructions below, refer to the details given on page 8:
THIS UNIT USES ONLY COMPRESSED AIR. CHECK THAT THE CONTAINER
HAS NOT BEEN DAMAGED (IT COULD EXPLODE). THE MAXIMUM PRES-
SURE IS 10 BAR. THE MAXIMUM TEMPERATURE WITH WHICH THE UNIT
CAN WORK IS 40°C.
With the potentiometer for regulating the output current (9), set a
suitable value for the thickness that is to be cut, in agreement with the
line capacity.
- Turn the switch on the front panel (6).
46
ENGLISH
THOR 103
COD. 6909500060
STEL s.r.l. – Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail: stel @ stelgroup.it
http: www.stelgroup.it
TECHNICAL
DESCRIPTION
6.0– INSTALLATION
6.1– CORRECT CUTTING POSITION
During use of the machine the operator must stand at the front so as to
prevent the fumes produced by cutting from being sucked into the
machine by the cooling fans (through the front and side ventilation
openings.
6.2– STARTING UP
The operator may start up the machine only after having read and
understood all parts of this manual. Depending on the type of cut to be
performed he must follow the work phases described below.
6.3- INSTRUCTIONS FOR USE
1- Ensure that the work environment and your clothing satisfy the safety
requirements described on PAGE 3.
2- Position the generator in a place where there is no obstacle to air
circulation.
3- Connect the THOR to a suitable power socket (an earthed socket is
obligatory).
4- Connect the compressed air pipe to the air filter on the rear panel.
-5- Ensure that there is no water in the filter. If necessary, empty the
filter.
For the instructions below, refer to the details given on page 8:
THIS UNIT USES ONLY COMPRESSED AIR. CHECK THAT THE CONTAINER
HAS NOT BEEN DAMAGED (IT COULD EXPLODE). THE MAXIMUM PRES-
SURE IS 10 BAR. THE MAXIMUM TEMPERATURE WITH WHICH THE UNIT
CAN WORK IS 40°C.
With the potentiometer for regulating the output current (9), set a
suitable value for the thickness that is to be cut, in agreement with the
line capacity.
- Turn the switch on the front panel (6).
46
ENGLISH
THOR 103
COD. 6909500060
STEL s.r.l. – Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail: stel @ stelgroup.it
http: www.stelgroup.it