During Use - GGP ITALY B 26 J Traducción Del Manual Original

chine.
– A lways wear slim-fitting protective clothes,
anti-vibration gloves, protective goggles, half-
mask respirator, protective earplugs, anti-
shear safety boots with non–slip soles.
– N ever wear scarves, shirts, necklaces or any
hanging or flapping accessory that could
catch in the machine.
– T ie your hair back if it is long.
2) Thoroughly inspect the entire work area and
remove anything that could be thrown by the
machine or damage the cutting means (stones,
branches, iron wire, bones, etc.).
3) Before using the machine, check its general
condition and in particular:
– T he throttle trigger and the safety lever must
move freely, they must not need forcing and
should return automatically and rapidly back
to the neutral position;
– T he throttle trigger must remain locked until
the safety lever is pressed;
– T he engine stop switch must easily move from
one position to the other;
– T he electric cables and in particular the spark
plug cable must be in perfect condition to
avoid the generation of any sparks, and the
cap must be correctly fitted on the spark plug;
– T he machine handgrips and protection devic-
es must be clean and dry and well fastened to
the machine;
– C heck the correct position of the handgrips
and the connection point of the harness, and
the proper balance of the machine.
– M ake sure that the guards are suitable for the
cutting means being used and are fitted cor-
rectly.
– T here must be no signs of damage on the
cutting means. Make sure the cutting means
is not worn or damaged. Replace the dam-
aged or worn cutting means to preserve bal-
ance. Any repairs must be done at a special-
ised centre.
4) WARNING: DANGER! Petrol is highly
flammable.
– K eep the fuel in containers which have been
specifically manufactured and homologated
for such use;
– a dd fuel, using a funnel, only outdoors; do not
smoke during this operation and each time fu-
el is handled;
– S lowly open the fuel tank to allow the pressure
inside to decrease gradually;
– Add fuel before starting the engine. Never re-
move the tank cap or add fuel while the engine
is running or when the engine is hot;
– i f you have spilled some fuel, do not attempt to
ignite the engine but move the machine away
from the area of spillage and avoid creating
any source of ignition until the fuel has evapo-
All manuals and user guides at all-guides.com
– A lways put the tank and fuel container caps
– I mmediately clean up all traces of fuel spilt on
– N ever start the machine in the same place you
– M ake sure your clothing does not come into
5) Replace faulty or damaged silencers.
1) Do not operate the engine in a confined space
where dangerous carbon monoxide fumes can
develop.
2) Work only in daylight or with good artificial
light in good visibility conditions. Keep per-
sons, children and animals away from the work-
ing area.
3) Always use caution and take on a firm and
well-balanced position
4) Where possible, avoid working on wet, slip-
pery ground or in any case on uneven or steep
ground that does not guarantee stability for the
operator;
5) Make sure you have a steady foothold on
slopes.
6) Never run, always walk.
7) Pay particular attention to uneven ground or
the presence of obstacles.
8) Always work across the face of the slope
and never up and down it, being very careful
when changing direction, making sure the cut-
ting means is always downstream.
9) Do not use the machine if you are unable to
hold it with both hands or keep it steady on your
legs while working.
10) The machine must never be used by more
than one person.
11) When working, the machine must always be
firmly held in both hands, keeping the power unit
on the right of the body and the cutting-means
assembly below the line of the belt.
14) Pay attention to traffic when using the ma-
chine near roads.
13) Never use the machine with damaged or
missing guards.
14) Always keep hands and feet away from the
cutting means, when starting and when using
the machine.
15) Beware of injuries caused by devices used
to cut the line length. After releasing the new line,
always put the machine in a working position be-
fore starting the engine.
16) Be careful of flying debris coming from the
3
rated and fuel vapours have dissipated:
back on and tighten well;
the machine or on the ground;
refilled it with fuel; the engine must be started
in an area at least 3 metres from where you re-
filled the fuel tank;
contact with the fuel, on the contrary, change
your clothes before starting the engine.
C) DURING USE