Preparing To Work; Checking The Machine; Preparing The Fuel Mixture - GGP ITALY B 26 J Traducción Del Manual Original

– I nsert the supplied wrench (3) in the specif-
ic hole of the inner ring-nut (1), then turn the
ring-nut by hand and push the wrench (3) until
it enters the hole of the angle transmission (2),
blocking rotation.
– F it the cutting line head (11) screwing it anti-
clockwise.
– R emove the wrench (3) to restore rotation.
b) Adjusting the guard
– F it the additional guard (5), inserting the cou-
plers into the respective seats in the guard (6)
and pressing until a click is heard; then fasten
in place using the screw (10).
WARNING! When using the cutting line
head, the additional guard, with line cutting
knife, must always be fitted.
c) Disassembly
– I nsert the supplied wrench (3) in the specific
hole of the inner ring-nut, then turn the ring-
nut by hand and push the wrench (3) until it
enters the hole of the angle transmission (2),
blocking rotation.
– R emove the cutting line head (4) unscrewing it
clockwise, making sure not to slide the spacer
(1a) off the shaft.
1.4 MOUNTING THE ROD
(Models with separate rod – Fig. 6)
– P ull out the stop pin (1) and push the lower
part of the rod (2) right down until the stop pin
(1) clicks into the hole (3) in the rod. This is
easier to do if you rotate the bottom of the rod
(2) slightly in both directions. The pin (1) is in
place when it is completely lodged in the hole.
– O nce inserted, tighten the knob (4) securely.

2. PREPARING TO WORK

2.1 CHECKING THE MACHINE

Before starting work please:
– c heck that all the screws on the machine and
the cutting device are tightly fastened;
– c heck that the cutting device is undamaged
and that the 3 or 4-point metal blades (if fitted)
are properly sharpened;
– c heck that the air filter is clean;
– c heck that the guards are suited to the cutting
device being used, properly fastened and ef-
ficient;
– c heck the handgrips are well fastened.

2.2 PREPARING THE FUEL MIXTURE

This machine is fitted with a two-stroke engine
All manuals and user guides at all-guides.com
which requires a mixture of petrol and lubricat-
ing oil.
IMPORTANT Using petrol alone will damage the
engine and is cause for invalidation of the war-
ranty.
IMPORTANT Use only quality fuels and oils to
maintain high performance and guarantee the du-
ration of the mechanical parts over time.
2.2.1 Petrol characteristics
Only use unleaded petrol with a fuel grade of at
least 90 ON.
IMPORTANT Unleaded petrol tends to create de-
posits in the container if preserved for more than 2
months Always use fresh petrol!
2.2.2 Oil characteristics
Only use top quality synthetic oil specifically for
two-stroke engines.
Your Dealer can provide you with oils which have
been specifically developed for this type of en-
gine, and which are capable of guaranteeing a
high level of protection.
The use of these oils makes it possible to pre-
pare a 2,5% mixture, consisting in 1 part oil to
40 parts petrol.
2.2.3 Preparation and preservation
highly inflammable!
– K eep the petrol and fuel mixture in homolo-
– Never leave the containers within the reach
– N ever smoke whilst preparing the mixture
To prepare the fuel mixture:
– P lace about half the amount of petrol in a ho-
– Add all the oil, according to the chart.
– Add the rest of the petrol.
– C lose the top and shake well.
IMPORTANT The fuel mixture tends to age. Do
not prepare excessive amounts of the fuel mixture
to avoid the formation of deposits.
IMPORTANT Keep the petrol and fuel mixture
containers separate and easily identifiable to
7
of the fuel mixture
DANGER! Petrol and the fuel mixture are
gated fuel containers, in a safe place, away
from any flames or heat sources.
of children.
and avoid inhaling the petrol fumes.
mologated tank.