Descargar Imprimir esta página

TSM WILLMOP 35 Instrucciones Originales página 30

Fregadora vertical

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 57
WILLMOP 35, 35 S
OPERATING MANUAL
1.1).
Once the handle has been released, it is free to move at 360° without any constraint, and the whole weight of the handle is
supported by the joint designed by TSM (Fig. 12).
The handle is also equipped with a capacitive system that detects the presence of the user through the contact of the hands on
the handle itself. To activate the cleaning program chosen on the console, simply grab the handle with one or two hands and
operations will start.
To use Willmop 35 the user only needs to hold the handle and by light twisting of the hand (or hands) he can change the direction.
WARNING
– To correctly turn the Willmop 35 on, the cleaning program on the console must be chosen before
grabbing the handle with one or two hands. If the user chooses the program on the console, having his hand (or both)
positioned on the handle, he will need to remove it (or remove both) and place the hand (or hands) back, in order to
activate correctly the program selected.
If the user removes both hands from the handle when it is in operation, Willmop 35 goes on stand-by, and all the
functions in use will be turned off. It is sufficient to re-grab the handle to resume the functions.
The stand-by status remains until one of the following situations occurs:
 the user grabs the handle again.
 the user moves the program selector on the console to the OFF position.
 the battery runs out completely.
 Willmop 35 switches off due to prolonged inactivity.
WARNING
– If the Willmop 35 is left in stand-by mode for more than 15 minutes, the Willmop 35 switches off
automatically. It is necessary to turn the program selector to the OFF position to reset, wait a few seconds, and turn the
selector to the desired cleaning program.
To switch off Willmop 35 completely it is necessary to move the program selector on the console to the OFF position. In the event
that the vacuum motor was in use, it will be switched off and lifted up automaticaly to allow the collection of any water residues
still on the ground.
9.8 Squeegee inclination
During operation the rear squeegee blade must work slightly bent backwards evenly over its entire length.
9.9 Empty the tanks
It is necessary to empty the dirty water or water with detergent, into an appropriate drain. To clean the recovery tank thoroughly,
fill it partially with fresh water and keep it in a horizontal position. Tilt the tank repeatedly, thoroughly rinsing off any dirt deposited
inside the tank (Fig. 13).
WARNING
- Please observe the local regulations regarding the disposal of wastewater treatment solutions.
9.10 Transport / displacement of Willmop 35 inside a building
To move Willmop 35 from one position to another inside a building, lock the handle in the vertical position (Fig. 1). Make sure to
have completely emptied the tanks. Make sure to have completely emptied the water tanks, and tilt Willmop 35 backwards,
pivoting on the rear wheels and helping yourself with the handle (Fig. 14). In this way Willmop 35 can be moved on wheels,
pushing the handle in the desired direction like a common cart.
WARNING
- To prevent water dripping on the floor, it is essential to empty the water tanks before transporting
Willmop 35.
Be careful when moving Willmop 35 over edges, barriers or gratings.
9.11 Lifting Willmop 35 up
To lift Willmop 35 it is required to lock the handle in the vertical position, remove the tanks and the battery to make it lighter. Then
lift it with both hands. One hand positioned on the handle and the other in the handle of the frame (Fig. 13).
WARNING
- To prevent the risk of injury and damage, keep in mind the weight of Willmop 35 during transport and
lifting.
9.12 Parking Willmop 35
Lock the handle in the vertical position (Fig. 1). Make sure to have completely emptied the tanks. Make sure not to leave the
battery completely discharged, recharge it if necessary.
WARNING
- Make sure that Willmop 35 is parked on a smooth surface with no slopes.
If Willmop 35 is not used regularly, keep the battery charged in a dry and clean place. Make sure the battery is charged
monthly.
30

Publicidad

loading

Este manual también es adecuado para:

Willmop 35 s