Publicidad
Idiomas disponibles
Idiomas disponibles
stable until the ACTUAL internal core temperature reaches the
PRESET Internal core temperature. The oven will then let the
chamber temperature drop slowly until it reaches the hold tem-
perature and keeps it stable (Hold temperature mode).
NOTE: there is no timer function in this case.
Pause
When the oven is in operation, the oven will PAUSE if the
"START/PAUSE" (5) button has been pressed and resume oper-
ation (with temperature settings unchanged) when the "START/
PAUSE" button is pressed again.
Switch OFF
When the oven is in the operation mode or hold mode, you can
switch off the oven by pressing the standby button (1) (the oven
is in standy mode now). Power indicator light (7) is still ON, but
all other indicator lights (8) to (11) will be off. Switch off: turn off
the green ON / OFF switch at the rear side to the "0" position. If
not present, then remove the plug from the socket.
If needed reverse the door
It is possible to reverse the door according to the following in-
structions.
(Fig.2-6 on page 3-4)
• Switch off the appliance and disconnect the power supply.
• Wait until the appliance has cooled down.
• Remove any food trays inside the chamber.
• Lay down the appliance on the side so that the hinge of the
door is on the top. (Fig.2 on page 3)
• Use a flat screw driver to losen the screw and remove the
door hinges. (Fig.3 on page 3)
• Remove the door.
• Use a flat screw driver to unscrew the bolt on the door's
frame top part and reverse the bolt position. (Fig.4 on page 4)
• Lay the appliance sideway on the other side.
• Reassemble the door. (Fig.5 on page 4)
• Reinstall the hinge. (Fig.6 on page 4)
• Position the oven in horizontal position and reconnect the
power supply.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
• No parts are dishwasher safe.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Problems
Possible cause
Appliance does not
No power at the
work
electrical outlet
Green on/off switch
at the rear side
The plug is not
plugged (correctly)
into the electrical
outlet
Appliance does
Heating element
not reach the set
defective
temperature
Control unit
defective
Heating element
fuse defective
GB
Possible solution
Check the fuse
Turn on the on/
off switch at the
rear side to the
position "I"
Check the plug
Contact the
supplier
9
Publicidad
