Descargar Imprimir esta página

Concept VP5076 Manual De Instrucciones página 25

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 40
EN
CHECKING THE CONTAINER CONTENT LEVEL
If the suction power is lower even though the nozzle is lifted above the floor, empty the container immediately.
NOTE: If the s uction power remains l ow after replacing the container, check for the following:
- some of the air passages (hoses, telescopic tube, suction inlet, brush adapter, or other adapters) are
obstructed;
- the motor filter is dirty;
- the air outlet filter is dirty.
Check for each of the possible causes above and eliminate the problem before you start vacuuming. If the
cause of the problem cannot be identified, hand over the product to the nearest service centre. Never use the
vacuum cleaner if the s uction power remains l ow . The motor could be damaged irreparably
MAINTENANCE
As a preventative measure, we recommend emptying the container and cleaning
the filters of the vacuum cleaner after each use.
EMPTYING THE CONTAINER
1.
Unplug the vacuum cleaner from the mains. Disconnect the hose from the
suction inlet.
2. Push the latches on the container holder, and shift the container upwards
(Fig. 3).
3.
Press the latch on the bottom of the r ear side of the container, open the latch
and empty the contents of the container (see Fig. 4).
4. Close the container and return it to the vacuum cleaner. Make sure the
container is positioned properly. You should hear a clicking sound from the
handle latches.
REPLACING FILTERS
• The filters should be cleaned or replaced when they are visibly dirty, or if the
appliance's suction power is reduced. Always check the filters after using the
appliance.
• In order to avoid damage to the appliance, do not use it with incorrectly installed
filters.
• Before replacing the filters, disconnect the appliance from the electrical socket.
• You can buy suitable types of filters from your dealer, or you can order them
from the manufacturer.
CLEANING THE INLET FILTERS
1.
Disconnect the flexible hose and remove the container.
2.
Open the filter holder on the f ront side of the container (Fig. 5) and remove
the filter (Fig. 6) .
3.
The foam rubber filter (Fig. 7) may be cleaned mechanically by shaking them
and cleaning with a soft brush. Heavily fouled filters can be washed after this
step and cleaned with a soft brush in lukewarm water. Do not use detergents.
It is important to let the wet parts dry thoroughly.
VP 5 075
48
EN
EN
Do not use a hair dryer for drying! Wet filters will be damaged if used for
vacuuming!
4. Assemble cleaned or new components and install them in the original
location using the reverse procedure.
Note: Wet cleaning can cause more wear and tear of the filter, and
a correspondingly shorter service life. If the vacuum cleaner does not
perform with the original suction power, the filters should be replaced with
new ones.
CHECKING AND REPLACING THE AIR OUTLET FILTER
1.
Press and o pen the air outlet grid at the rear section of the vacuum cleaner
(see Fig. 8).
2.
Remove the filter.
3.
The filter can be cleaned by tapping or shaking it. If the filter is extremely
dirty, it can be washed in lukewarm water. Let the filter dry completely
before using it again.
4.
Insert a cleaned or new air outlet filter, and close the air outlet grid.
F ig . 3
CLEANING AND MAINTENANCE
The vacuum cleaner and its accessories can be cleaned with a wet cloth.
Do not immerse the power cord, plug, or appliance in water or any other liquid.
Do not use aggressive substances for cleaning, such as solvents or abrasives!
TROUBLESHOOTING
Problem
F ig . 4
Motor does not run.
Motor has stopped
F ig . 5
operating.
Reduced suction power
Vacuum cleaner heats up
F ig . 6
VP5076
47
VP5076
48
Cause
Solution
Plug inserted into the
mains outlet incorrectly or
Check the plug connection.
insufficiently.
Check for voltage, e.g. by connecting
The mains outlet is not live.
another appliance.
Disconnect the cable from the socket.
Improper or insufficient air
Check and release the air suction
flow. Motor overheating
and discharge holes; check the filter's
fuse activated.
cleanliness and/or replace the dust bag.
Let the vacuum cleaner cool down.
Dust bin full or clogged.
Empty and clean the dust bin.
The filters are clogged
Clean or replace the filters.
Clogged nozzle, tube, or
Check and clear the air passage on the
hose.
suction and discharge sides.
Slight heating of the vacuum cleaner is normal and cannot be considered
a failure.
EN
F ig . 7
F ig . 8
VP 5 075
49

Publicidad

loading