Publicidad
Idiomas disponibles
Idiomas disponibles
WARNINGS!
GB
1. Never switch on the machine if the bowl lid is missing. Before
removing the bowl lid, switch off the machine and unplug it.
2.
There are some moving parts inside the bowl, which
may cause injuries, switch off the machine and un-
plug it before carrying out any operation.
c) Start operating the machine:
(Control panel : Fig.2 on page 3)
Each bowl is controlled independently.
• First, connect the power plug to a suitable electrical power
outlet.
• Next, press (21) to switch ON the machine. Press and hold
(21) for 3 seconds to switch to STANDBY mode of the machine
when not use. (Fig.8 on page 5).
• Then, press the corresponding bowl button (12).
And press consecutively to select the working mode. There
are 3 working modes: Granita (18) , juice (19) or OFF (20). It
will be displayed in sequence and the corresponding icon will
be lighted.
I). To serve with Granita
(Fig.9 on page 5)
• Press the corresponding bowl button (12).
• Next, press consecutively to select Granita mode, (18) will be
lighted.
• Then, press "+" or "-" consecutively to adjust the hardness.
The level in between from 1 (Soft with much water content) to
7 (Hard with less water content).
II). To serve with cold drinks
(Fig.10 on page 5)
• Press the corresponding bowl button (12) until (19) lights up.
• Enter to juice temperature setting mode by long pressing (22)
until "PR" is blinking on the display.
• Press (22) again to select bowl 1(F1) or 2(F2) until "F1" or "F2"
is shown on the temperature display.
• Press left panel (17) to adjust the temperature from 1°C ~ 7°C.
The temperature will be set successfully. After flashing 15
times without any operation, the display will return to normal.
NOTICE:
• Current temperature is showing on display as normal.
• Press (14) and (16) at the same time for restoring to default
temperature( 2°C ).
• Display shows "PR" / "F1" / "F2" : Juice temperature setting
mode / bowl 1 / bowl 2. The mode will become invalid after
flashing 15 times without any operation and display will switch
back to normal.
• Only left panel (17) can be operated (for both bowl 1 and 2)
within juice temperature setting model.
III). To stop working
• Press the corresponding bowl button (12).
• Next, press consecutively until OFF mode, (20) will be lighted.
Then, it would stop stirring and refrigerating.
d) To simply clean the corresponding bowl:
• Press and hold the corresponding bowl button (12) for about
6 seconds.
• The corresponding bowl valve will be fully open for cleaning
about 3 minutes. During this mode, the control display will
show "°C".
14
ATTENTION! Under this mode, the electronic expansion valve of
the corresponding bowl will open. But the auger still stirring for
cleaning. Please fill with warm and clean water into the bowl
not exceeding the "MAXIMUM LEVEL". Do not put your hand in-
side.
Switch OFF the machine and unplug it for thorough cleaning or
sanitization to the machine.
e) Dispensing granita
(Fig.11 on page 6)
• To dispense the food product, pull the tap lever.
NOTE: Regularly check the temperature of the beverages in the
bowl (2). Keep on the machine running when there is any
food inside the bowl.
If the machine is not continuously operated, it is necessary to
dispose of the small amount from the tap area first before serv-
ing for the customer.
Parameter Setting of the Machine
WARNING! It is highly not recommended to change
these settings below as the machine is already adjusted to the
optimal settings by the factory default. Change the setting only
if it is necessary.
How to set
Press and hold (22) for about 6 seconds. The "PA" is shown on
the display.
Press "+" or "-" to enter the value "15" (This is the code for
entering into the setting mode).
Then, press (22) consectively to select the parameter (display
will show consectively) that you want to change. The parame-
ters are list below:
Display
Description
Temperature of Bowl I under
F1
juice mode
Temperature of Bowl II under
F2
juice mode
F3
Protection when the tempera-
C1
ture is low
Liquid temperature during
C3
first stage
Liquid temperature during
C4
second stage
Sensor probe temperature
A1
for bowl I
Sensor probe temperature
A2
for bowl II
A3
Temperature difference under
E1
juice mode
E2
Time delay of compressor
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
Setting
Factory
range
default
1°C ~ 7°C
2°C
1°C ~ 7°C
2°C
Not applicable
-13°C ~ -3°C
-5°C
5°C ~ 10°C
10°C
3°C ~ 8°C
5°C
-5°C ~ 5°C
0°C
-5°C ~ 5°C
0°C
Not applicable
1°C ~ 5°C
2°C
2 ~ 8 min
2 min
Publicidad
