Publicidad
Idiomas disponibles
Idiomas disponibles
• Next, insert the auger with the white washer (D) and black
GB
washer (E) for the shaft. Rotate the auger to engage it. (Fig.22
on page 7)
• After that, set back the bowl in place, slightly raise head of the
auger so that it align wth the position (E) of the bowl. (Fig.23
on page 7)
• Press the bowl slightely downward until it engages with the
correct position and there will be a "click" sound. (Fig.24 on
page 7)
Follow below instructions to re-assembly the tap (7):
• Using the supplied lubricant, lubricate the cap (Y) adequately
and re-assembly the components.
• Fit the pin (F) while keep the tap lever steady. (Fig.25 on page
8)
• Replace the tap seal ring (C) if worn or leakage.
f) Rinsing the machine
ATTENTION! Before starting up the machine after cleaning, you
must carry ou the rinsing cycle.
Procedures as below:
• Pour out the clean water into bowl;
• Let the machine to run for at least 5 minutes in the "agitation"
• Switch off the machine and empty the bowl by opening the
tap.
g) Cleaning the drip tray
ATTENTION! The drip tray should be emptied and cleaned every
time the red float installed in the grid rises into view. It should
be cleaned daily.
• Lift the tray with the grid on top of it and pull it out. (Fig.26
on page 8)
• Wash the tray and the grid separately with the lukewarm wa-
ter.
• Dry both parts well and place back the grid on top of the tray.
• Position the drainage hose in the opening provided.
• Fit back the tray in place and press down to secure it with
the machine.
h) Lighting lid
ATTENTION! During the cleaning process, take care not to
bend, break or damage the „contacts" (Fig.27 on page 8). Any
damage might cause a bad functioing of the lighting lid.
• Clean the lid contacts using a damp cloth and dry well. Always
switch OFF the machine.
• Do not immersed in water for cleaning.
i) Bulb replacement
• The bulb should be replaced only when the machine is
switched OFF and the power cord is unplugged.
• Next, remove the protection caps. Then, using a proper
screwdriver (not supplied) to loosen the screws in order to
remove the cover (Fig.28 on page 8).
• Remove the bulb (U) from the socket (T) (Fig.29 on page 8).
And replace it with a new bulb (not supplied).
j) Cleaning the condenser
• ATTENTION! The condenser can only be cleaned solely by a
specialized technician, who must organize all of the opera-
tional sequences and with suitable tool/equipment.
• The condenser should be cleaned regularly (at least once per
16
every 6 months) to keep good machine performance.
• To access the condenser, the safety guards need to be re-
moved.
• WARNING! Removing safety guards will expose some sharp
surfaces of the machine.
• To remove the safety guard panel, proceed as below:
(Fig.30 on page 8)
1) Lift and completely remove the upper part of the side guard;
2) Loosen the 4 screws securing the guard in place.
3) After removing the 4 screws, take off the safety guard. (Fig.31
on page 8)
4) Use a dry brush (not supplied) to remove the dust that has
built up over time with use. (Fig.32 on page 8)
5) After having thoroughly cleaned the condenser, re-assembly
the safety guard.
k) Periodic maintenance
This machine must be periodically checked (for at least every 6
months) by a specialized technician. This periodic check serves
to ensure that all the components installed and the machine
itself are at a high level of safety.
Any worn components must be replaced by an original spare
part. It is forbidden to use this machine when even only one of
its components is faulty or worn. User are prohibited to perform
periodic maintenance.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
Publicidad
