nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Clean the inside of container with a non-abrasive detergent
and rinse with clean water.
• Never immerse the appliance in water or other liquids.
• No parts are dishwasher safe.
Parts
How to clean
All accessories
• Soak in warm,
such as racks, rack
soapy water for
holders, etc.
about 10 to 20
minutes.
• Rinse under
running water
thoroughly.
External glass
• Wipe clean with
surfaces
a soft cloth and
a little neutral
detergent. Make
sure no water or
moisture enters
inside the of the
appliance.
Interior glass
• Remove any food
surfaces
deposits.
• Wipe clean with
Glass door
a soft cloth and
a little mild
detergent. Make
sure no water or
moisture enters
inside the of the
appliance.
a) Emptying the bowls
• Before a bowl may be cleaned, it must be emptied all the food
ingredient inside the bowl first.
b) Disassembly the dispensing tap:
• Ensure all the beverage are emptied inside the bowl.
• Disassembly the tap before removing the bowl.
• Remove the pin (F) to release all the other parts. (Fig.13 on
page 6)
• Use clean and warm water to wash the parts. (Fig.14 on page
6)
c) Remove the bowl and the lid:
• To remove the bowl lid (1) of the bowl (2) first, follow these
instructions & see Fig.15 on page 6.
1) Lift the rear part of the lid;
2) Extract the bowl lid (1) from the retainer placed at the
• Then, raise the front part of the bowl to release it.
• Next, remove the bowl from its position by pushing slightly at
the rear side. The bowl is detached now. (Fig.16 on page 6)
• Finally, take out the auger and remove the seal hat cover (A)
and bowl seal ring (B). Replace if worn or for every 12 months.
(Fig.17 on page 7)
d) Remove the bowl and the lid:
ATTENTION! All of the previously disassembled and removed
components must be thoroughly washed and sanitized. We
strongly recommend daily cleaning and sanitizing this machine
in order to maintain high degree of food quality.
• To carry out this procedure correctly, proceed as follows:
- Fill a container with detergent and hot water with a temper-
ature of 50 ~ 60°C;
- Wash the disassembled components thoroughly with the de-
tergent solution.
- Rinse with hot water.
- Dip the disassembly components into the solution and soaked
for about 30 minutes.
Remark
- Then, wash the components again with clean water.
Dry all parts well
- Place different components on a dry, clean surface and dry
at last.
all parts well.
- Assembly the machine as described in below part e).
- Before starting operating the machine again, carry out the
rinsing cycle with clean water. (See below part f).)
WARNING! Do not immerse the bowl lids with lighting bulb in
any type of liquid. Before cleaning, please make sure the light-
ing bulb are removed from the machine as described as below
(Fig.29 on page 8).
To clean the lighted bowl lid as below:
1. Using a clean, damp cloth to wipe clean the bottom part of
the bowl lid & the outer surface.
2. Using a sponge dipped in the washing solution, sanitize the
bottom part (24) of the bowl lid, take care not to touch the
hinge part (X) for about 10 minutes (Fig.18 on page 7).
3. Rinse twice or more, with a clean sponge soaked in warm
fresh water.
4. Dry it with a dry clean cloth.
5. Put back the bowl lid only after the bowl has been cleaned
and sanitised.
e) Reassembly the washed components
ATTENTION! All of the washed components must be carefully
re-assembled. Some components must be adequately lubricat-
ed by the supplied lubricants in order to ensure that they work
efficiently.
• Always check for the integrity of the seal (A), should it be
worn, replace it with a new one (supplied).
• Replace the auger seal hat cover (A) for at least every 12
months.
• Insert the auger seal hat cover (A) as below. (Fig.19 on page
7).
• Lubricate the inside area of the auger seal hat cover (A) as
shown in Fig.20 on page 7 with the lubricant (Supplied).
• Then, insert the bowl seal ring (B) and lubricate with the sup-
plied lubricant around it as below. (Fig.21 on page 7)
front side.
GB
15