Denon DCD-980 Instrucciones De Operación página 12

ENGLISH
PLAYBACK USING THE REMOTE CONTROL UNIT ___
The accessory RC-235 remote control unit can be used to control the CD
player from a convenient distance.
(1) Inserting the dry cell batteries
1. Remove the battery cover on the back of the remote control unit.
2. Insert two R6P (standard size AA) dry cell batteries with correct
polarity as indicated inside the battery compartment.
3. Replace the battery cover.
Notes on the Batteries
e The remote contro! unit uses standard size AA dry cell batteries.
e The batteries will need to be replaced approximately once a year.
Replacement may be necessary earlier depending on how much the
remote contro! unit is used.
e If, in less than a year from the time new batteries were inserted, the
remote control fails to operate the CD player from a near-by position, it
is time to replace the batteries.
REMOTE CONTROL UNIT RC-235
Randam Button (RANDOM)
Display Button (DISPLAY)
Press this button to change the brightness of
the display.
Press once to make the display 2/3 as bright as
normal.
Press again to make the display 1/3 as bright as
normal.
Press once again to turn the entire display off
during playback and all but the track number off
in any other mode.
Number Buttons (0 ~ 9)
Play Button { >» PLAY)
Pause Button ( I PAUSE)
Stop Button ( HJ STOP)
Pitch — Button (PITCH —)
Pitch + Button (PITCH +)
Checking Programmed Contents
By pressing the CALL button on the remote control
unit, programmed contents will be displayed.
Tracks entered into the memory, will be displayed
starting from the first track entered, and will
advance one step at a time each time the CALL
button is pressed.
e insert the batteries properly, following the polarity diagram inside the
battery compartment, in other words make sure (+) and (—) terminals
are properly aligned.
e Batteries are prone to damage and leakage.
Therefore:
e Do not combine new batteries with used ones.
e Do not combine different types of batteries.
e¢ Do not jumper opposite poles of the batteries, expose them to heat,
break them open nor expose of them in open fire.
e If the remote control unit is not to be used for a long period of time,
remove the batteries from the unit.
© Ifthe batteries have leaked, remove any traces of battery fluid from the
battery compartment, wiping thoroughly with a dry cloth. Then insert
new batteries.
{2) Directions for Use
e Operate the remote contro! unit while pointing it towards the
remote control sensor on the CD player (see below).
Right 30°
Remote contro! sensor
Left 30°
When a remote control signal is received, the remote control indicator on
front of the CD player lights briefly.
e The remote control unit can be used at a distance up to 8 meters in a
straight line from the CD player. This distance decreases if there are
obstructions blocking the signal path or when the remote control unit is
operated at an angle from the remote control sensor.
e The buttons on the remote control unit have identical functions with
those on the CD player.
However, the following functions cannot be remote controlled: Power
ON/OFF.
Setting to the Program Mode
e For program search, press the PROG/DIRECT
button then the number buttons (0 through 9
and +10).
e@ The remote control unit is normally set to the
direct mode.
Program/Direct Button (PROG/DIRECT)
+10 Button
Call Button (CALL) The level of the Variable Output
Terminal output can be varied.
Pressing the (+) button increases
the volume and pressing the (—-)
button decreases the volume.
Volume Buttons (+)
Volume Buttons (-—)
Automatic Search Forward Button ( PPI)
Automatic Search Reverse Button ( Iq )
Manual Search Forward Button ( PP )
Manual Search Reverse Button ( 44 )
Track Selection
Use the numeric track buttons (0 ~ 9 and +10)
while programming and to access a desired track
almost instantly.
The track search buttons ( I¢€q and PPI) are best
used to advance or return from the current track to
the next track.