Publicidad
Idiomas disponibles
Idiomas disponibles
Programming (continued)
Programmable Inputs
•
The controller contains three programmable inputs
that may be configured to accept several different
input devices.
•
Navigate through the menus to SYSTEM SETTINGS
(enter password) to PROG INPUTS. Select INP1,
INP2 or INP3.
•
Select a Function from the list. Press Enter.
•
Select a Polarity from the list. Press Enter.
Function Options:
•
Non-monitored Eye/Edge Input
•
Car Dealer Input (typically loop detector, treadle
hose, card reader)
•
Timer Defeat
•
All Fly (previously known as FSTS)
Radio
The controller has a built in Security+ 2.0® radio receiver,
that can program up to 90 remote control devices and up
to 30 keyless entry devices.
Programming Remote Controls
and myQ® Devices
1.
Select SYSTEM SETTINGS from the main menu
(enter passcode: 326)
2.
Select CONNECTIVITY.
3.
Select one of: Learn myQ Devices or Remotes.
4.
The operator will indicate the selected accessory is
being learned.
5.
Repeat as needed for any other devices and
remotes.
Note: Remotes are disabled from moving the door while
accessing the programming menus. Exit the menus
before testing the remotes.
Resetting Remote Controls and
myQ® Devices
1.
Enter the menu and navigate to SYSTEM SETTINGS,
and enter the password.
2.
Navigate to CONNECTIVITY.
3.
Enter the UNLEARN submenu.
•
To unlearn remotes, select REMOTES.
•
To unlearn myQ devices, select MYQ
DEVICES.
4.
Save your changes by selecting SAVE.
5.
Exit the menu by holding the UP and STOP buttons
on the wall control.
Reset Defaults
Parameter
Operating Mode
Timer to Close
Mid-Stop
Maintenance Alert
System
Limits
Battery Options
Programmable Inputs
(1-4)
User Adjusted Speed
Wi-Fi Credentials
SKU/Model ID
LiftMaster Monitored
device(s)
Cable Tension Monitor
device(s)
Service Counter Interval 5000 cycles
Absolute Cycle Counter
Alarm
NOTICE: This device complies with part 15 of the FCC rules and
Innovation, Science and Economic Development Canada license-
exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
This device must be installed to ensure a minimum 20 cm (8 in.) distance
is maintained between users/bystanders and device.
This device has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC rules and
Industry Canada ICES standard. These limits are designed to provide
reasonable protection against harmful interference in a commercial
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
45
Default Value
C2
0 sec.
Deactivated
Deactivated/Enabled
Reset
Reset (AC fail is reset to door
close, and low battery is reset
to close and hold)
Unlearned
Maximum speed.
Learned
Learned (Can be changed in
the maintenance menu)
Deleted from memory (must
be disconnected prior to
reset)
Not Reset
Reset to "ON"
Publicidad
