Kärcher B 110 R Manual Del Usuario página 19

Installing the suction bar
1. Pivot both clamping levers upwards.
Suction hose
1
Suction bar suspension
2
Suction bar
3
Clamping lever
4
2. Insert the suction bar in the suction bar mount.
3. Pivot both clamping levers downwards.
Batteries
Recommended battery packs
ATTENTION
Risk of damage
Batteries may only be replaced with batteries of the
same technology.
Lead batteries must not be replaced by Li-Ion batteries
Li-ion batteries must not be replaced by lead batteries.
Lead batteries:
Description Order no. Volume
3
(m )*
170 Ah - 4.039-352.7 2,4
Maintenance-
free, AGM
180 Ah - 4.039-354.7 3,8
Maintenance-
free, gel
285Ah - Main- 4.039-353.7 12,6
tenance-free,
AGM
* Minimum volume of battery charging room
** Minimum air flow between battery charging room and
environment
The device requires 2 batteries.
Li-ion batteries:
Description
80 Ah, 25.6 V
The device requires 2 batteries.
Installing and connecting batteries
Note
In the case of the device variant with Li-Ion battery, the
battery is already installed and connected.
CAUTION
Removing and installing the batteries
Unstable machine position
Ensure that the machine is positioned stably when re-
moving and installing the batteries.
ATTENTION
Incorrect connection polarity
Destruction of the control electronics
Take care to ensure the correct polarity when connect-
ing the batteries.
ATTENTION
Deep discharge
Risk of damage
Charge the batteries before starting the device.
1. Drain the waste water.
2. Unlock the waste water tank and pivot it to the rear.
3. Place the battery in the device.
170 Ah, 4.039-352.7
Spacer 310x85x70 mm
1
Spacer 240x55x30 mm
2
180 Ah, 4.039-354.7
Spacer 310x85x70 mm
1
285 Ah, 4.039-353.7
Airflow
Spacer 345x60x47
1
3
(m /h)**
1,0
1,6
5,1
160 Ah Li-Ion, 6.654-454.0
Order no.
Plate
1
6.654-454.0
Spacer 155x300x60
2
Spacer 320x90x40
3
4. Insert the spacers at the locations shown in the pic-
ture between the battery and the device.
5. Connect the battery terminals using the connecting
cables.
6. Clamp the connecting cable on the (+) and (-) bat-
tery terminals that are still free.
Note
For the 170 Ah 4.039-352.7 battery set, attach the con-
nection cable to the negative pole with the insulated
pole screw.
7. Connect the device-side battery connector to the
battery-side battery connector.
8. Pivot the waste water tank forwards and close it.
Activating the Li-Ion battery
Li-Ion batteries are delivered in transport mode and
must be activated before initial startup of the device.
1. Charge the battery (see "Initial startup/Charging the
battery"), this will end the transport mode.
CAUTION
Removing and installing the batteries
Unstable machine position
Ensure that the machine is positioned stably when re-
moving and installing the batteries.
WARNING
Risk of injury due to the device tipping over!
Device may tip over when removing and installing bat-
teries.
Ensure that the device is positioned stably when remov-
ing and installing the batteries.
1. Turn the key-operated switch to "0" and remove the key.
2. Disconnect the battery connector.
3. Drain the waste water.
4. Pivot the waste water tank upwards.
Removing the battery
English
5. Disconnect the device-end cable from the negative
terminal at the battery.
6. Disconnect the remaining cables from the battery.
7. Remove the battery.
8. Dispose of the used batteries in accordance with
statutory provisions.
Initial startup
Charging the battery
DANGER
Inappropriate use of the charger
Electric shock
Adhere to the mains voltage and fuse values specified
on the device type plate.
Only use the charger in dry rooms with sufficient venti-
lation.
Flammable gases are generated when the battery is
charged
Risk of explosion
Only charge the battery in a suitable room. The room
must have a minimum volume depending on the battery
type and an adequate air exchange rate with a minimum
air flow (see "Recommended batteries").
ATTENTION
Accumulation of dangerous gases under the tank
during the charging process
Risk of explosion
Pivot the waste water tank upwards before charging
low-maintenance batteries.
The average charging time is approx. 10-15 hours.
The device cannot be used during the charging process.
Note
The device has deep discharge protection, i.e. the
brush motor and turbine are switched off automatically
when the permitted minimum capacity level is reached.
1. Drive the device directly to the charger and do not
drive on slopes.
Setting the charging characteristic
Before the initial startup, after a service reset or when
changing to a different battery type, it is essential to set
the charging characteristic.
DANGER
Danger due to the device inadvertently starting up
Risk of injury
Disconnect the spark plug connector or disconnect the
battery before performing any work on the device.
ATTENTION
Risk of damage to the battery
The service life and charging capacity of the battery can
be affected by an incorrect charging characteristic.
Make sure that the battery characteristic curve that
matches the battery is selected in the machine.
The currently selected battery characteristic curve can
be seen on the display or via the app in the "Device sta-
tus" area during charging.
Note
The charging characteristic can only be adjusted by
Kärcher Service.
Battery characteristics are available for the following
batteries:
● EXIDE GF12105V
● HOPPECKE TB115
● EXIDE GF12076V
● EXIDE FF12080W
● TROJAN 27TMX
● HOPPECKE TB80
● ZENITH L120185
Note
To enable the use of other batteries as well, a custom
battery characteristic curve can be created by the
Kärcher service department.
External charger
ATTENTION
Risk of damage due to unsuitable charger!
Do not connect the charger to the device-side battery
connector.
Use only a charger suitable for the type of battery in-
stalled.
Battery Capacity
4.039-352.7 170 Ah
4.039-354.7 180 Ah
4.039-353.7 285Ah
1. Unlock the waste water tank and pivot it up.
2. Pull out the device-side battery connector.
Charger
6.654-436.0
6.654-434.0
6.654-419.0
19