Controls And Functions - SYNQ DMC 2000 Manual De Instrucciones

ENGLISH
INSTALLATION GUIDELINES:
 Placing and using the unit for long periods near heat-generating sources such as amplifiers, spotlights,
etc. will affect its performance and may even damage the unit.
 Take care to minimize shocks and vibrations during transport.
 When installed in a booth or flight case, please make sure to have good ventilation to improve heat
evacuation of the unit.
 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when
bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full
performance.
 Choose the place where you put your installation very carefully. Avoid presence of heat sources. Avoid
places with vibrations or places that are dusty and humid.
 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
 In order to prevent electric shock, do not open the top cover. If a problem occurs, contact your dealer.
 Do not place metal objects or spill liquid inside the player. Electric shock or malfunction may result.
 The player should not be adjusted or repaired by anyone except properly qualified service personnel.
 This unit may cause interference to radio and television reception.
CLEANING THE PLAYER:
Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside the unit. Do not
use volatile liquids such as benzene or thinner which will damage the unit.

CONTROLS AND FUNCTIONS

1. MAINS input: connect the unit to the 100-240V AC mains, using the supplied power-cord.
2. POWER ON/OFF switch: switches the unit on and off.
3. USB2 connection: this is the second (type-A) USB-connection, used to connect any USB mass storage
device that was formatted in FAT or FAT32. By default this input is used to connect a hard disk. (see
chapter "connections")
4. MIDI / LINK USB connection: this (type-B) USB-connection is used to connect the player to a computer
with MIDI DJ-software. Please check the chapter "connections" for more information.
5. MASTER BALANCED OUTPUT: The XLR-connectors can be used to connect this mixer to any
balanced amplifier input or powered speakers, using special balanced signal cables.
6. MASTER UNBALANCED OUTPUT: The "master" output has the same output signal as the balanced
master output(5) but unbalanced.
7. BOOTH MASTER OUTPUT: The "booth master" output carries the same signal as the master but can
be controlled independently by the booth master (49). Use the outputs to connect unbalanced amplifiers
or connect a sound recorder.
8. PH/LINE SWITCH: This switch makes it possible to switch between the Phono and the Line input level
for this channel.
9. ANALOG INPUT: to both mixer channels you can connect turntables or extra CD-players that can be
mixed simultaneously with tracks from the DMC2000 players and DJ-software from your PC/MAC.
10. GROUND (GND) CONNECTION: Many Turntables have a GND-connection. It is preferable to connect
this signal ground to the GND-connector. If your turntable does not have a ground wire, you don't have
to use this connector.
11. DJ MIC INPUT JACK: Combo jack. Accepts either a balanced microphone with an XLR connector or an
unbalanced microphone with 1/4" mono jack. This input is mainly used as DJ-microphone. The talkover
does not affect the signal level of this input.
SYNQ 3/120
®
OPERATION MANUAL
DMC2000
ENGLISH
12. KENSINGTON SECURITY SLOT: can be used to protect the DMC2000 from opportunist theft. Keep in
mind that this is absolutely not a 100% anti-theft protection! You can buy a compatible "Kensington"
security cable from almost every computer store.
13. USB1 connection: this is the first (type-A) USB-connection, used to connect any USB mass storage
device that was formatted in FAT or FAT32. By default this input is used to connect an occasional USB-
drive like USB-sticks etc.
14. SOURCE SELECT switch: use this button to select the desired audio source: USB1 or USB2.
15. DATABASE / NEXT TRACK button: a very important button if you want to find your next track easily
and fast, even while the previous track is still playing! This button works in two different ways:
 NEXT TRACK function: will be used while searching on mass storage devices that don't have the
"Q-DBase system" files installed. You can only search on track and folder numbers.
 DATABASE function: will be used while searching mass storage devices that have the "Q-DBase
system" files installed. You can alphabetically search on artist, track title, genre or album. Very fast
and no need for you to know where your files are located!
Once you have found the desired song, just press the LOAD TRACK-button (19) to load the track.
For both functions, please refer to chapter "HOW TO USE" for more information.
16. FOLDER knob: this knob has different functions:
 No Q-Dbase: turn this knob to browse the folders of USB-drive while you don't use the Q-Dbase
system.
 During Q-Dbase search: press while you turn the knob to select the first character of the search key
you're looking for. Turn the knob to go to the next search key that starts with the same character.
Press the knob to show the search key on the 2
 Setup menu: turn the knob to browse the different menu options.
Please refer to chapters "HOW TO USE" & "SETUP MENU" for more information.
17. TRACK knob: this knob has different functions:
 No Q-Dbase: turn this knob to browse the tracks inside a folder of a storage device while you don't
use the Q-Dbase system.
 Q-Dbase search: two options:
SYNQ 4/120
®
OPERATION MANUAL
nd
text line of the display.
DMC2000