Installation And Operating Instructions; General Safety Instructions; Introduction; Symbols Used In This Document - Grundfos Oxiperm OCD-164 Manual De Instalación Y De Mantenimiento

English (GB) Installation and operating instructions
Original installation and operating instructions
Contents
\
1. General safety instructions
1.1 Introduction
1.2 Purpose of this manual
1.3 Symbols used in this document
1.4 Users
1.5 Obligations of the operator
1.6 Maintenance and service personnel
1.7 Correct usage
1.8 Inappropriate usage
1.9 Safety and monitoring equipment
1.10 Chemicals
2. Technical data
2.1 General data
2.2 Electrical data
2.3 Delivery state
3. Fundamentals
3.1 Chlorine dioxide for water treatment
3.2 Functional sequence
4. Design and function
4.1 Design of the system
4.2 Components
4.3 Mode of operation of the system
5. Installation
5.1 Transport and storage
5.2 Unpacking
5.3 Installation location
5.4 Installation scheme
5.5 Wall mounting
5.6 Hydraulic connection
5.7 Electrical connection
5.8 Interfaces RS-232, -422 and -485
6. Operation of control electronics
6.1 Program structure
6.2 Control and display elements
6.3 Automatic mode
6.4 Manual operation
6.5 Logbook
6.6 System choice
6.7 Units
6.8 Setup
6.9 Local/remote
7. Commissioning
7.1 Directives
7.2 System choice
7.3 Selection of operation mode
7.4 Venting of the bypass line
7.5 Calibrating the dosing pumps
7.6 Adjusting the dosing controllers
8. Operation of the system
8.1 Automatic operation
8.2 Manual operation
8.3 Faults
8.4 Error messages of the controller
8.5 Fuses and LEDs of the controller
8.6 Possible faults when changing the tank
9. Maintenance
9.1 Maintenance of the dosing pumps
9.2 Maintenance of the suction lines
9.3 Maintenance of reactor
9.4 Maintenance of injector
10. Spare parts kits and spare parts
10.1 DMI dosing pumps with double-head system
10.2 DMI dosing pumps with single-head system
10.3 Dosing pumps DMX 221
10.4 Bypass, post mixer, and dosing controller
10.5 Enclosure exhaust device
4
10.6 Bypass with solenoid valve and flow limiter (standard
version: solenoid valve)
10.7 Bypass, circulating pump 230 V - 50 Hz, 120 V - 60 Hz 46
10.8 Bypass (version solenoid valve/ball valve, batch mode) 47
Page
10.9 Bypass for external booster pump
4 11. Accessories
11.1 External booster pump
4
11.2 Load unit for booster pump
4
4 11.3 Hose connections/hose
5 11.4 Gas sensor and gas warning device
5
12. Current setting data
5
13. Quick Guide
5
14. Disposal
5
5

1. General safety instructions

5
7

1.1 Introduction

7
The OCD-164 disinfection system is a state-of-the-art solution,
9
which complies with recognised safety regulations.
9
Conformity with applicable standards, directives and laws has
10
been verified. Nevertheless, certain risks which cannot be
10
prevented by the manufacturer are associated with the use of the
10
system.
11
1.2 Purpose of this manual
11
12
• Inform users of optimum use of the system.
12
• Warn users of possible residual risks when using the system
13
correctly, and identify measures that should be taken to avoid
13
damage.
13
• Caution users against obvious misuse or inappropriate use of
13
the system, and inform them of the necessary care that must
14
be taken when operating the system.
16
16

1.3 Symbols used in this document

17
19
Warning
20
If these safety instructions are not observed, it may
20
result in personal injury.
21
21
If these safety instructions are not observed, it may
Caution
21
result in malfunction or damage to the equipment.
21
22
Notes or instructions that make the job easier and
Note
22
ensure safe operation.
22
Information about possible residual risks can be found:
25
• on warning signs located at the installation site, and
26
• immediately before steps associated with a residual risk.
26
26
26
29
31
32
33
33
35
36
37
38
38
39
39
39
40
41
42
42
43
43
43
44
45
49
50
50
52
52
52
53
54
54