Best KITE 800 Manual Del Usuario página 37

Push button P1: LIGHTS . Switches on and off the lights.
Push button P2: MOTOR: Switch on and off the motor. Switch on the motor to
the latest used speed and if pressed different
times changes the speed in a cyclic way (1,2,3,4,1,2.....) The speed set is
visualized by the icon D5 and simultaneously
the icon D8 switches on ( the speed of the rotational movement is proportional
to the speed ). To the maximum speed
the icon D8 switches off and the icon D3 switches on.
To switch off the motor, press the push button P2 for about 2 seconds (the set
speed is memorized).
Push button P3: Select the functions D4 (Sensor) and/or D7 (Air Refresh).
Push button P4: Reset grease filters and/or charcoal filters.
Icon D1: GREASE FILTERS. It switches on when the grease filter must be
cleaned (after about 30 hours of working).
One time the grease filter is cleaned, to make the hours calculation start again,
press the push button P4.
Icon D3 : MAXIMUM SPEED. Is activated only when the maximum speed is set.
Icon D4: SENSOR: To activate the sensor function, press the push button P3.
To disconnect the sensor, repeat the same
operation. When the sensor activated, the hood switches on automatically in the
presence of any kinds of odours or vapours,
smokes or heat, caused by the cooking process and also in the presence of
possible and anomalous gas emissions in
environment.
Icons D5 and D6: DISPLAY. Displays the set speed; displays the sensor
sensitivity.
Icon D7: AIR REFRESH: To start the function Air refresh, press the button P3
until the icon D7 flashes. To deactivate
the Air Refresh function, press the button P3 until the icon D7 goes off.
The function Air Refresh activates only if the motor is not working. Starting the
function Air Refresh, the hood recycles
the air in the environment in perfect silence, starting every 5 minutes (for 10
minutes, at the first speed).
NOTE: The Sensor and Air Refresh functions can be activated simultaneously
by pressing the button P3 until both the
icons (D4 and D7) come on.
Icon D8 : ENGINE ON. The icon switches on when the engine is at the first,
second or third speed. To the fourth speed,
the icon switches off and the icon starts working to the maximum speed (icon
D3).
Icon D10: CHARCOAL FILTERS ( For the hood in the filtering version).
It switches on when it is time to replace the charcoal filter/s (after about 120
working hours). One time the charcoal filter/
s is replaced, to make the hours calculation start again press the button P4.
Sensor sensitivity: the sensor sensitivity can be modified by simultaneously
pressing the buttons P3 and P4 (the value
set appears on the display D5 and may be between 1 and 9). To modify this
value press the button P3. To confirm, press
the button P4 (or it will automatically be confirmed after 5 seconds).
FILTER ALARM: see Icon D1 and Icon D10.
Warning: in order to avoid damaging the sensor, never use silicone products
near the hood!
WHEN TO REPLACE IT: replace it at least every 6 months.
HOW TO REMOVE IT:
Replacing the lamps
- To change the halogen bulbs open the cover levering from the proper
slots.
- Replace with lamps of the same type.
WARNING: Do not touch the new lamp with bare hands.
Replace with lamps of the same type.
If thr light spot is damaged, it must be replaced only by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard
MALFUNCTIONS
If something appears not to be working properly, do the following simple
checks before calling Technical Service:
• If the hood is not working:
Check that:
- The power has not been disconnected.
- A speed has been selected.
•
Check that:
-
vapours released.
-
-
• If the hood has turned off during normal functioning:
Check that:
- The power has not been disconnected.
- the omnipolar disconnection device has not tripped.
This appliance is marked according to the European directive 2002/96/EC on
Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused by inappro-
priate waste handling of this product. The symbol on the product indicates that this
product may not be treated as household waste. Instead it shall be handed over
to the applicable collection point for the recycling of electrical and electronic
equipment. Disposal must be carried out in accordance with local environmental
regulations for waste disposal. For more detailed information about treatment,
recovery and recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
Components not provided with the product