Recognition Of Limit Positions On Opening And Closing With The Use Of Mein Family Inverter - Nice NDCC4001 Instrucciones Y Advertencias Para La Instalación Y El Uso

03. Press the [Set] key for 3 seconds
to confirm position A1.
LED L1 stays on.
LED L5 flashes: programming po-
sition AP
04. If you do not wish to program the partial opening position, quickly press
the [Set] key twice to move to the new programming stage. LED L5
stays off.
Otherwise continue the sequence.
05. Use the [Open] or [Close] key to move the door to the partial opening
position.
06. Press the [Set] key for 3 seconds
to confirm position AP.
LED L5 stays on.
LED L8 flashes: programming po-
sition A0
07. Use the [Open] or [Close] key to move the door to the maximum
closing position.
08. Press the [Set] key for 3 seconds
to confirm position A0.
LED L8 stays on.
09. When the [Set] key is released, all LEDs are switched off.
10. Send an opening command by pressing the [Open] key to perform a
complete opening manoeuvre.
Close L1 L2 L3 L4 L5 L6 L7 L8
BusT4
Open Stop Close Fuse 3.15AF
Open
Set
to push
PP
buttons
OSE
Stop 8K2
to internal
control
DIC1
to internal
-20° C +55° C
brake
Bluebus
2
Flash N19771
11. Send a closing command by pressing the [Close] key to perform a
complete closing manoeuvre.
L1 L2 L3 L4 L5 L6 L7 L8
Close
BusT4
Stop Close Fuse 3.15AF
Open
Open
Set
to push
PP
buttons
OSE
8K2
Stop
to internal
control
DIC1
to internal
-20° C +55° C
brake
Bluebus
2
Flash N19771
CAUTION! – The learning phases must never be interrupted. If this oc-
curs, the entire learning procedure must be repeated. At the end of the
learning phase, if LEDs "L3" and "L4" flash, this means that there is an
error. The position recognition procedure can be repeated at any time
also after the installation.
10
3.15 - Recognition of limit positions on opening and closing with
3"
5 positions can be programmed, as described below:
Close L1 L2 L3 L4 L5 L6 L7 L8
BusT4
Open Stop Close Fuse 3.15AF
Open
Set
to push
PP
buttons
OSE
Stop 8K2
to internal
control
DIC1
to internal
-20° C +55° C
brake
Bluebus
2
N19771
Flash
3"
L1 L2 L3 L4 L5 L6 L7 L8
Close
BusT4
Open Stop Close Fuse 3.15AF
Open
Set
to push
PP If the door is in the closing position, it must be positioned manually at about
buttons
OSE
8K2
Stop
to internal
control
DIC1
to internal 50 cm from the ground by using the emergency manoeuvre system (see motor
-20° C +55° C
brake
Bluebus
2
Flash N19771
instruction manual) to prevent, in case of inverted rotation, the load-bearing
ropes (sectional doors) from leaving their seat or the excessive tightening of the
shutter (rolling shutters).
3" Caution! - If the direction of rotation does not correspond to the direc-
tion set (Open = opening direction), you must leave the "Recognition
of opening and closing positions" procedure and activate the function
"Inverted rotation direction"; refer to Table 5.
Close L1 L2 L3 L4 L5 L6 L7 L8
BusT4
Open Stop Close Fuse 3.15AF
Open
Set To carry out the procedure, proceed as described below:
to push
PP
buttons
OSE
Stop 8K2
to internal
control
DIC1
to internal
-20° C +55° C
brake
Bluebus
2
N19771
Flash
the use of MEIN family inverter
Position LED Meaning
A1 L1 Maximum opening position. When the door reaches
this position it stops
RA1
L2 Position when the deceleration starts during the open-
ing manoeuvre. When the door reaches this position,
the motor decelerates and reaches the minimum
speed.
AP L5 Partial opening position. It is the position in which the
door stops after giving a partial opening command.
RA0
L7 Position when the deceleration starts during the clos-
ing manoeuvre. When the door reaches this position,
the motor decelerates and reaches the minimum
speed.
A0
L8 Maximum closing position. When the door reaches this
position it stops.
01. Press and hold down [Set] and
[Close] keys for 3 seconds to
start the position memorisation
phase.
LED L1 flashes: programming po-
sition A1
02. Use the [Open] or [Close] key to move the door to the maximum
opening position.
03. Press the [Set] key for 3 seconds
to confirm position A1.
LED L1 stays on.
LED L2 flashes: programming po-
sition RA1
04. If you do not wish to program the opening deceleration position, quick-
ly press the [Set] key twice to move to the new programming stage.
LED L2 stays off.
Otherwise continue the sequence.
05. Use the [Open] or [Close] key to move the door to the opening de-
celeration position.
06. Press the [Set] key for 3 seconds
to confirm position AP.
LED L5 stays on.
LED L7 flashes: programming po-
sition RA0
07.
If you do not wish to program the partial opening position, quickly press
the [Set] key twice to move to the new programming stage. LED L5
stays off.
Otherwise continue the sequence.
08. Use the [Open] or [Close] key to move the door to the partial opening
position.
Close L1 L2 L3 L4 L5 L6 L7 L8
BusT4
Open Stop Close Fuse 3.15AF
Open
Set
to push
PP
buttons
OSE
Stop 8K2
to internal
control
DIC1
to internal
-20° C +55° C
brake
Bluebus
2
N19771
Flash
3"
L1 L2 L3 L4 L5 L6 L7 L8
Close
BusT4
Open Stop Close Fuse 3.15AF
Open
Set
to push
PP
buttons
OSE
Stop 8K2
to internal
control
DIC1
to internal
-20° C +55° C
brake
Bluebus
2
Flash N19771
3"
Close L1 L2 L3 L4 L5 L6 L7 L8
BusT4
Open Stop Close Fuse 3.15AF
Open
Set
to push
PP
buttons
OSE
Stop 8K2
to internal
control
DIC1
to internal
-20° C +55° C
brake
Bluebus
2
N19771
Flash