Technical Data; Operation; Initial Operation - Bosch Active Line Serie Manual Original

Technical Data

Battery Charger Wide Range Charger (36–4/100-230)
Article number
Rated voltage V~
Frequency Hz
Output voltage V
Charging current A
Charging time, approx.
– PowerPack 400 h
– PowerPack 500 h
Operating temperature °F
Storage temperature °F
Weight, approx. lb
Degree of protection

Operation

Initial Operation

Connecting the Charger to Household Electricity
2
2
3
 Note the household voltage! The voltage of the power
supply must correspond to the specifications given on
the battery charger nameplate.
Plug the charger plug 3 of the power cord into the charger
socket 2 of the charger.
Connect the power supply cable (country-specific) to the
household electricity supply.
Use only the supplied input connection: standard AC power
cord (3 in the diagram) when connecting to the household
electrical supply.
Bosch eBike Systems
238
English–6
Compact Charger (36–2/100-240)
0 275 007 906 0 275 007 915
90...264 90...264
47...63
36
4
3.5
4.5
+32...+104 +32 ...+104
+14...+122 +14 ...+122
1.8
IP 40
Charging the Removed Battery
11
6
9
5
8
6
5 Charge connector
6 Socket for charge connector
8 Rack-type battery pack
9 Operation and charge-control indicator
10 Battery On/Off button
11 Standard battery pack
Switch the battery pack off and remove it from the holder of
the eBike. To do this, read and follow the operating instruc-
tions for the battery pack.
 Put the battery pack down only on clean surfaces. In
particular, avoid getting the charge socket and the con-
tacts dirty, e.g., with sand or soil.
Insert the charger plug 5 for the battery charger into the
socket 6 on the battery pack.
0 275 U07 XCX | (3.5.16)
English–7
Charging the Battery on the Bike
47...63
36
2
6.5
7.5
7
1.3
IP 40
5
10
7
Switch the battery off. Clean the cover of the charge socket
7. In particular, prevent the charge socket and the contacts
from getting dirty, e.g., with sand or soil. Lift the cover of
the charge socket 7 and plug the charge connector 5 into
the charge socket 6.
 Charge the battery only in accordance with all safety
instructions. If this is not possible, remove the battery
from the holder and charge it in a more suitable location.
When doing so, read and follow the operating instruc-
tions for the battery.
0 275 U07 XCX | (3.5.16)
Charging with Two Battery Packs Inserted
If two battery packs are mounted on one eBike, both bat-
tery packs can be charged using the unsealed connection.
The charging process will charge both battery packs alter-
nately, automatically switching between both battery
packs numerous times. The charging times add up.
11
Both battery packs are also discharged alternately during
operation.
If you take the battery packs out of the holders, you can
charge each battery pack individually.
Charging Procedure
The charging procedure begins as soon as the charger is
connected to the battery or the charge socket on the bike
6
and the main power supply.
Note: The charging procedure is only possible when the
temperature of the eBike battery pack is within the permis-
sible charging temperature range.
Note: The drive unit is deactivated during the charging pro-
cedure.
The battery can be charged with or without the on-board
computer. When charging without the on-board computer,
8
the charging procedure can only be observed on the bat-
6
tery charge-control indicator.
If the on-board computer is connected, a corresponding
message will be output on the display.
The charging state is displayed by the battery charge-con-
trol indicator 9 on the battery and by the bars on the on-
board computer.
During the charging procedure, the LEDs for charge-control
indicator 9 on the battery pack light up. Each continuously
lit LED is equivalent to a charge capacity of approx. 20 %.
The flashing LED indicates the charging of the next 20 %.
Once the battery is fully charged, the LEDs extinguish imme-
diately and the on-board computer is switched off. The
5
charging procedure is terminated. The charging state can be
displayed for 3 seconds by pressing the On/Off button 10.
Disconnect the charger from the main power supply and
the battery pack from the charger.
When disconnecting the battery pack from the charger, the
battery pack is automatically switched off.
Note: If you have charged on the bike, carefully close the
charge socket 6 with the cover 7 after the charging proce-
dure so that no dirt or water can get in.
If the charger is not disconnected from the battery after
charging, after a few hours the charger will switch itself
back on, check the charging state of the battery and begin
the charging procedure again if necessary.
Bosch eBike Systems
239