Commissioning; Operating Characteristics; Proper Use; Guidelines For Spine Board Use - Spencer ROCK PIN Manual De Uso Y Mantenimiento

CHARACTERISTICS
Length (mm)
Width (mm)
Thickness (mm)
Weight (with bag and accessories) (kg)
Maximum load capacity (kg)
Material
CHARACTERISTICS
Dimensions (mm)
Materials
Weight (kg)
CHARACTERISTICS
Dimensions (mm)
Materials
Weight (kg)
9.

COMMISSIONING

For first use, check that:
• Packaging is intact and has protected the device during transportation
• Check that all parts included in the packing list are present
• General functionality of the device
• Product cleanliness
• Absence of cuts, holes, tears or abrasions on the entire device.
See paragraph 11 for how to carry out the above-mentioned checks.
Do not modify the device or its parts for any reason as this could cause damage to the patient and/or rescuers.
Failure to take the above measures will preclude safe use of the device, resulting in risk of damage to the patient, operators and the device itself.
For subsequent use, perform the operations specified in paragraph 12.
If the above conditions are met, the device may be considered ready for use; otherwise, you must immediately remove the device from service and contact the Manufacturer.
Do not alter or modify the device arbitrarily, as doing so could result in unpredictable operation and damage to the patient or rescuers and will void the warranty and
release the Manufacturer from all liability.

10. OPERATING CHARACTERISTICS

See paragraph 11 - Proper use for operating characteristics.

11. PROPER USE

Primary medical evaluations must be carried out before intervening on the patient.

11.1 GUIDELINES FOR SPINE BOARD USE

Before using the spine board, you should carefully read the user manual for all accessories that you plan to use with the board, such as belts, cervical collars, head restraints
and ankle restraints.
Strictly follow the local emergency service guidelines before placing the patient on
the spine board.
Carefully assess the need for a cervical collar, head restraint or other immobilization
aids in addition to the necessary restraint belts.
Baby Go has 4 zones of different depths in relation to the patient support surface. The
side to be used must be assessed by the rescuer in order to improve the alignment
of the cervical section, compensating for the different occipital prominence typical
of pediatric patients.
To separate Baby Go from the adult spine board, rotate the red clips 90° so that the
pediatric board can be removed.
Once the board has been used, place it back into the adult board by turning the same
clips as before, making sure that the two devices are correctly attached as shown
in the image.
The spine boards can be used to perform preliminary X-ray diagnostics to confirm or refute the hypothesis of the presence of spinal lesions on the patient.
Tango should not be used in MRI rooms.

11.2 APPLYING IMMOBILIZATION ACCESSORIES

After positioning the patient, it is essential to apply restraint belts or spider straps in accordance with the user manual for these devices.
If the patient's condition requires and/or allows it, apply a head restraint, neck brace, cervical collar until an adequate degree of immobilization is achieved.
Make sure that the patient is correctly immobilized.

11.3 LIFTING THE PATIENT

Never use cranes, slings or other systems to lift the device.
Lifting is only permitted by hand and by an appropriate number of operators (minimum 4).
Operators must be positioned symmetrically and in such a way to allow safe, stable lifting of both the head
and foot sides of the spine board.
If the 4 minimum operators foreseen (illustrated in red) is not sufficient to ensure the safety of operations,
two additional operators (illustrated in blue) must hold the device in the central area in order to distribute
the load as best as possible.
The maximum load on each operator must never exceed the maximum load permitted by work safety
regulations.
HORIZONTAL FIXING
545x25x65 ± 5 mm per piece
1,5 ± 0,2 kg
PEDI LOC
1220
250
30
4,5
30
Pvc/Wood/polyurethane
VERTICAL FIX BOARD
Upper part
570x25x65 ± 5mm
Steel, Nylon, Brass
nd
WALL SUPPORT FOR BABY GO
282x80x38 mm
Nylon
150 g
Lower part
180x50x55 ± 5mm
IT
EN
DE
FR
ES
PT
EL
CS
17