Areas Of Use; Filling The Fuel Tank - Stiga PRIMO Instrucciones De Uso

3.4.6 Cutting deck (1:C)
3.4.6.1 Transport position – Cutting position
(1:G)
Pedal for transport position – cutting posi-
tion.
Raising the deck to the transport position:
1. Depress the pedal (1:G) fully.
2. Turn the catch (1:F) to the right.
3. Release the pedal.
Lowering the cutting deck to the cutting position:
1. Depress the pedal (1:G) fully.
2. Release the pedal.
3.4.6.2 Engaging the cutting deck (1:L)
The cutting deck must never be en-
gaged when in the transport position.
This will damage the belt transmission.
Lever for engaging and disengaging the cutting
deck.
Two positions:
1.Front/lower position – cutting deck dis-
engaged.
2. Rear/upper position – cutting deck en-
gaged.
3.4.6.3 Setting the cutting height (1:H)
The cutting height can be set in 9 fixed positions
using the lever (1:H).
3.4.7 Seat (1, 5:A)
The seat can be folded and adjusted front-
rear. To adjust the seat, loosen the screws
attaching the seat to the seat plate, set the
seat to the desired position and tighten the
screws. Tightening torque: 20-24 Nm.
If the screws are tightened more than 24
Nm, the seat will be damaged.
The seat is equipped with a safety switch that is
connected to the machine's safety system. This
means that certain dangerous activities are not pos-
sible when there is nobody sitting on the seat. See
also 5.4.2.
3.4.8 Engine casing
The machine may not be operated un-
less the engine casing is folded down.
Risk of burns and crushing injuries.
In order to inspect and carry out maintenance on
the engine, the engine casing must be opened.
Opening:
The engine must not be running when
the casing is opened. Risk of serious in-
jury.
All manuals and user guides at all-guides.com
ENGLISH
1. Fold the seat forward.
2. Grip the casing at the front edge (6:Q) and fold
Closing:
Grip the casing at the front edge and fold the cas-
ing down. Then reset the seat.
The machine must only be used for cutting grass in
private gardens.
NOTE! This machine is not intended to be driven
on public roads.
5.1 TRANSPORTATION
If the machine is transported on a flatbed or trailer,
the machine must be pushed or lifted off/on. The
machine must never be driven off/on with the en-
gine running as driving on slopes requires great
care and the maximum permitted incline can easily
be exceeded. Also see "5.5.2" and "5.5.3".

5.2 FILLING THE FUEL TANK

Always use lead-free petrol. You must never use
2-stroke petrol mixed with oil.
NOTE! Normal unleaded petrol is perishable and
must not be stored longer than 30 days.
Environmental petrol can be used, i.e. alkylate pet-
rol. This type of petrol has a composition that is
less harmful for people and nature.
Fill with petrol as follows:
1. Fold the seat up.
2. Open the fuel cap (6:R).
3. Fill with petrol carefully.
4. Reinstall the fuel cap and fold the seat down.
the casing up rearwards.

4 AREAS OF USE

5 STARTING AND OPERATION
The machine may not be operated un-
less the engine casing is closed. Risk of
burns and crushing injuries.
Never drive the machine off a trailer
with the engine running. Risk of the
machine tipping over and causing ma-
terial damage or fatal injury.
Petrol is highly inflammable. Always
store fuel in containers that are made
especially for this purpose.
Only fill or top up with petrol outdoors,
and never smoke when filling or top-
ping up. Fill up with fuel before starting
the engine. Never remove the filler cap
or fill with petrol while the engine is
running or still warm.
EN
55