Descargar Imprimir esta página

Stiga PRIMO Instrucciones De Uso página 59

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 92
6.8 DECK BELT (21:J)
After 5 hours of operation check that the machine's
belts are intact and not damaged.
6.9 ADJUSTING THE DRIVE CHAIN
Adjust the belt tension by moving the tensioner
each season, or when needed, as follows:
1. Slacken off the nuts (15:T)
2. Set the tensioner wheel by tightening the screw
(15:U) with use of the fingers.
3. Tighten the nuts (15:T).
6.10 LUBRICATION
All lubrication points according to the table below
must be lubricated after every 25 operating hours
as well as after each clean.
Item
Section below
Drive chain
6.10.1
Steering cable
6.10.2
Tensioning arms
6.10.3
and moving joints
Throttle cable
6.10.4
6.10.1 Drive chain
Lubricate the drive chain (15:U) using chain spray
as follows. Use universal type chain spray.
1. Trestle up the machine's right-hand rear wheel
so that it can rotate freely. See 6.3.
2. Brush the chain clean using a wire brush.
3. Rotate the rear wheel by hand and at the same
time spray the chain so that it is fully lubricated.
4. Lower the machine.
6.10.2 Steering cable
See fig. 16. Lubricate the steering cable using
chain spray as below. Use universal type chain
spray.
1. Brush the chain clean using a wire brush.
2. Turn the steering wheel and at the same time
spray the cable so that it is fully lubricated.
6.10.3 Tensioning arms moving joints
Lubricate the bearing points using an oil can at the
same time as activating the respective control.
Preferably carried out by two people.
Activate the controls:
• Steering
• Clutch, brake
• Raise the cutting deck
• Engaging the cutting deck.
• Setting the cutting height
All manuals and user guides at all-guides.com
ENGLISH
6.10.4 Throttle cable
See fig. 17. Lubricate the cable ends using an oil
can at the same time as activating the respective
control.
6.11 BATTERY
Figure
The battery is a valve-regulated battery with 12 V
15:U
nominal voltage. The battery fluid does not need to
16
and cannot be checked or topped up. The only
maintenance that is required is charging, for exam-
-
ple after extended storage.
17
6.11.1 Charging with the engine
The battery can also be charged using the engine's
generator as follows:
1. Install the battery in the machine as shown be-
2. Place the machine outdoors or install an extrac-
3. Start the engine according to the instructions in
4. Allow the engine to run continuously for 45
5. Stop the engine. The battery will now be fully
6.11.2 Charging using battery charger
When charging with the battery charger, a battery
charger with continuous voltage must be used.
Contact your dealer to purchase a battery charger
with constant voltage.
The battery can be damaged if a standard type bat-
tery charger is used.
6.11.3 Removal/Installation
The battery is placed under the seat. See fig. 4.
During removal/installation of the battery, the fol-
lowing applies regarding connection of the cables:
• During removal. First disconnect the black ca-
Never overcharge the battery. Over-
charging can damage the battery.
Do not short-circuit the battery's termi-
nals. Sparks occur which can result in
fire. Do not wear metal jewellery which
can come into contact with the battery
terminals.
In the event of damage to the battery
casing, cover, terminals or interference
to the strip covering the valves, the bat-
tery should be replaced.
The battery must be fully charged be-
fore being used for the first time. The
battery must always be stored fully
charged. If the battery is stored while
discharged, serious damage will occur.
low.
tion device for the exhaust fumes.
the user guide.
minutes.
charged.
ble from the battery's negative terminal (-).
Then disconnect the red cable from the battery's
positive terminal (-).
EN
59

Publicidad

loading