Steering Wheel; Operating Procedure - Cub Cadet 17BICBDT603 Instrucciones De Funcionamiento Originales

English
Maintenance indicator (Type 2):
The maintenance indicator reminds
the user of the maintenance
intervals for changing the engine
oil and the air filter and outputs
warning signals for oil level and
battery voltage.
Changing the oil:
Every 50 operating hours
(oil change interval) the letters
– OIL – SOON – TIME
in succession on the display for
7 minutes.
Change the engine oil immediately,
see engine operating manual.
Oil level:
If the letters LO – OIL – TIME
in succession on the display, the
engine oil level is too low.
Switch off the engine immediately
and check the engine oil level, see
engine operating manual. Top up
the oil if required.
Battery voltage:
If the key is turned to the
position, the battery voltage is
displayed briefly and then the total
operating hours.
If the letters LO – BATT
appear in succession on the
display, the battery voltage is
too low (< 11.5 volts).
Recharge the battery as quickly
as possible as specified in the
"Maintenance" section of this user
handbook. Possibly have the
charging system checked by
a service centre for possible
damage.
Air filter maintenance:
Every 25 operating hours
(air filter maintenance interval) the
letters CLN – AIR – Filt
appear in succession on the
display for 7 minutes.
Service the air filter immediately,
see engine operating manual.
Notes:
– TIME means: The total operating
hours (see above) are displayed.
– If the oil change and air filter
maintenance intervals occur at
the same time, the oil change
display appears first and then
the air filter display.
8
PTO switch (8)
Fig. 6
The PTO switch actuates an
mechanical clutch to switch ON
and OFF the cutters.
ON = pull the switch.
OFF = press the switch.
Note
When the safety lock system has
CHG
automatically switched OFF the
appear
appliance (e.g. when reversing with
activated cutters), first switch ON
and then OFF the PTO switch to
release the lock on the clutch.
Can holder (9)
appear
Fig. 1
Ignition lock (10, depending
on model)
Ignition lock
Fig. 3a
Starting:
Turn key to the right
engine is running, then release.
Key is set to
Stopping:
Turn the key to the left, to
– TIME
Ignition lock with OCR function
Fig. 3b
This ignition lock features an OCR
function (= user-controlled mowing
in reverse gear).
Starting:
Turn key to the right
engine is running, then release.
The key at
allows mowing in the drive
direction.
OCR position:
Turn key to left of normal position to
reverse mowing position
– TIME
(1).
The indicator light (2) comes on
and indicates to the user that the
unit can now mow in reverse and
forward gear.
Stopping:
Turn the key to the left, to
Note
Do not use the OCR function
unless absolutely necessary,
otherwise work with the key in the
normal position. The OCR function
switches off automatically as soon
as the key is turned to the normal
until the
.
.
until the
(normal)
and press the switch
.
Operating Manual
position or the engine is switched
off (stop position or disconnection
of the engine by the safety interlock
system).
Storage bin (11)
Fig. 1
Gear release lever (12)
Fig. 9
To push the unit when the
engine is switched off.
Pull out both levers (near
each back wheel) and then press
them to the right.
To drive the unit, push the
lever to the left and press in.
Fuel tank (13)
Fig. 1
Adjustable seat
(14, optional)
Fig. 12
Pull the lever, and adjust the seat.

Steering wheel (15)

Fig. 1
Brake pedal (16)
Fig. 8
The brake pedal can be used
to brake quickly, to engage and
disengage the locking brake, and
to switch OFF speed control.
Note
The forwards and reverse
accelerator pedal must not be used
if the brake pedal is depressed.
This may damage the gears.

Operating procedure

Follow the instructions in the
engine handbook!
Danger
Risk of injury
No person, especially children,
and/or animals should be allowed
to stand close to the mower while it
is in use. They could be injured by
stones or similar objects that might
be thrown out. Children must never
be allowed to operate the mower.