Closed-Loop Crimp Terminals - Omron Q2 Serie Instrucciones De Instalación Y Funcionamiento

6 Attachments
Screw Adapter
Bit
M4
Bit
*1
M5
Bit
M6
Bit
M6
Bit
M8
Bit
M10
*1 When wiring drive models 2056 and 4089 and smaller, select the correct tools for the wire gauge.
*2 Use 6.35 mm (0.25 in) bit socket holder.
*3 Use a torque wrench that can apply this torque measurement range.
■

Closed-Loop Crimp Terminals

To comply with UL standards on drive models from 2257 and from 4208, use UL-approved closed-loop crimp
terminals. Use the tools recommend by the terminal manufacturer to crimp the closed-loop crimp terminal.
Closed-loop crimp terminals from JST Mfg. Co., Ltd. and insulation caps from Tokyo DIP Co., Ltd. are
recommended.
Comply with local standards for correct wire gauges in the region where the drive is used.
Contact the manufacturer or your nearest sales representative to order.
Note:
To comply with UL standards, use only insulated crimp terminals or crimp terminals with insulation tubing. Use UL-Listed, vinyl-
coated insulated copper wires for operation with a continuous maximum permitted temperature of 75 °C at 600 V.
Table 6.2 Closed-Loop Crimp Terminals and Insulation Caps (200 V Class)
Recommended Gauge (AWG, kcmil)
R/L1
Model
S/L2
T/L3
2004 - 2021 -
2030, 2042 -
2056 -
2070 - 2110 -
2138 -
2169, 2211 -
-
-
2257
2/0 × 2P 2/0 × 2P
-
122
Table 6.1 Recommended Wiring Tools
Bit
Model
SF-BIT-SL 1,0X4,0-70 PHOENIX CONTACT
SF-BIT-SL 1,2X6,5-70 PHOENIX CONTACT
SF-BIT-HEX 5-50 PHOENIX CONTACT
SF-BIT-SL 1,2X6,5-70 PHOENIX CONTACT
SF-BIT-HEX 6-50 PHOENIX CONTACT
SF-BIT-HEX 8-50 PHOENIX CONTACT
U/T1
V/T2 -, +1 +3
W/T3
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - 1/0 × 2P
- -
- 4/0 × 2P -
Torque Driver Model
(Tightening Torque)
Manufacturer
TSD-M 3NM
(1.2 - 3 N∙m)
Wire Gauge
≤ 25 mm
(AWG 10):
TSD-M 3NM
(1.2 - 3 N∙m)
Wire Gauge
≥ 30 mm
(AWG 8):
Terminal
Screw Size
10 M4
8 M5
6 M6
6 M6
4 M6
4 M8
3
-
M10
-
-
TOMPYEUOQ2A03C AC Drive Q2A Installation and Operation Instructions
Torque Wrench
Wire Gauge
2
≤ 25 mm
(AWG 10):
Wire Gauge
2 ≥ 30 mm
(AWG 8):
- 4.1 - 4.5 N∙m
- 5 - 9 N∙m
- 3 - 3.5 N∙m
- 8 - 12 N∙m
- 12 - 14 N∙m
Crimping Tool
Crimp
Terminal
Model
Tool Model Die Jaw
R5.5-4 YA-4 AD-900
R8-5 YA-4 AD-901
R14-6 YA-4 AD-902
R14-6 YA-4 AD-902
R22-6 YA-5 AD-953
R22-8 YA-5 AD-953
TD-224, TD-
R38-10
212
TD-225, TD-
R60-10
213
YF-1
YET-150-1
TD-227, TD-
80-10
214
TD-228, TD-
R100-10
214
-
2
-
2
*2 *3
*2 *3
*2 *3
*2 *3
*2 *3
Insulation
Cap Model
TP-005
TP-008
TP-014
TP-014
TP-022
TP-022
TP-038
TP-060
TP-080
TP-100