Publicidad
Idiomas disponibles
Idiomas disponibles
instruction manual
for use and maintenance serie MEC, STAR
DRAIN HOLE: on bi-directional motors with drain hole, the hole has to be connected to the oil tank through an hose of at least 22
mm of diameter. To avoid the forming of foam inside the tank, the hose has to be connected under the minimum level.
STARTING UP. Check that all circuit connections are exact and that the entire system is completely clean. Insert the oilin the tank, using a
filter. Bleed the circuit to assist in filling. Set the pressure relief valves to the lowest
possible setting. Turn on the system for a few moments at minimum speed, then bleed the circuit again and check the level of oil in the tank.
If the difference between pump or motor temperature and fluid temperature exceeds 10 °C, rapidly switch the system on and off to heat it up
gradually. Then gradually increase the pressure and speed of rotation until the pre-set operating levels as specified in the catalogue are attained.
PERIODICAL CHECKS – MAINTENANCE Keep the outside surface clean especially in the area of the drive shaft seal. In fact,
abrasive powder can accelerate wear on the seal and cause leakage. Replace filters regularly to keep the fluid clean. The oil level must be
checked and replaced periodically dependig on the system's operating conditions.
RESOLUTION PROBLEMS:
- Circuit is open. Downstream of the engine you have the oil reservoir and not the pump. If the engine remained in rotation with the engine off,
there will be overpressure, but cavitation. To solve this problem it would take a one-way valve that lists the oil or some of it through calibration,
the engine sent to his desire to avoid that the engine air pump.
- Circuit is closed. You could have an overpressure. To solve the problem or put an overpressure valve, as recommended in the key facility
attached or a calibrated one-way valve that bypasses the engine. Compared to the first case, the last option is cheaper and less invasive on a
system already exists as it does not require an additional hole in the tank.
HYDRAULIC MOTOR
Hydraulic Motor
Rotary blades
vacuum Pump
MEC 1000/H
PLM 20.20
MEC 1600/H
MEC 2000/H
KM 30.27
MEC 3000/H
MEC 4000/H
KM 30.43
MEC 5000/H
MEC 6500/H
MEC 8000/H
KM 30.51
MEC 9000/H
KM 30.73
MEC 11000/H
MEC 13500/H
KM 40.87
MEC 16500/H
KM 30.73
MEC 16500/H
MEC 2000/HM
MEC 3000/HM
MEC 4000/HM
MSA 125 SHA
MEC 5000/HM
MEC 6500/HM
MEC 8000/HM
STAR 60/H
KM 40.87
STAR 72/H
STAR 84/H
Table 1
pag. 40
Max pres-
Flow rate
sure of
exercise
1 bar
21,14 cm
/r
3
1 bar
26,7 cm
/r
3
1 bar
43,98 cm
/r
3
1 bar
51,83 cm
/r
3
1 bar
73,82 cm
/r
3
1 bar
86,56 cm
/r
3
0.9 bar
73,82 cm
/r
3
1 bar
125,7 cm
/r
3
1 bar
86,56 cm
/r
3
Rpm
Pressione
pressure
Hydraulic
system
1200
130 bar
200 bar
100 bar
1200
280 bar
150 bar
1200
120 bar
150 bar
250 bar
150 bar
185 bar
1200
230 bar
195 bar
1200
145 bar
180 bar
1200
145 bar
280 bar
1400
210 bar
1400
180 bar
180 bar
80 bar
90 bar
100 bar
540
175 bar
130 bar
140 bar
160 bar
130 bar
1000
155 bar
280 bar
190 bar
Max
Trasmitted
Power
4,7 kW
5 kW
6,8 kW
9 kW
11,3 kW
16,,4 kW
17,,2 kW
18,3 kW
21,4 kW
26 kW
26 kW
7,7 kW
8,7 kW
9,7 kW
12,5 kW
13,5 kW
15,5 kW
16 kW
19 kW
23,4 kW
Publicidad
