Starting; Filling The Tank - Efco Power MTT 3600 Manual De Instrucciones

tension (refer to Operation-Chain Tension
Section). Start the saw again and make a few cuts
in a log to heat up the chain. Stop the engine and
re-adjust chain again. Repeat this process until
the chain retains proper warm tension
adjustment in Operation-Chain Tensioning
Section. Never touch the ground with the
chain.
Bucking Spike
WARNING: Your chain saw is fitted with a
bucking spike. The bucking spike is very
sharp and can cause injury. Be extremely
careful when working near the bucking spike.

5. STARTING

FUELING
This product is powered by a 2-cycle engine and
requires pre-mixing gasoline and 2-cycle oil.
Pre-mix unleaded gasoline and 2-cycle engine oil
in a clean container approved for gasoline.
RECOMMENDED FUEL: THIS ENGINE IS
CERTIFIED TO OPERATE ON UNLEADED GASOLINE
INTENDED FOR AUTOMOTIVE USE WITH AN
OCTANE RATING OF 89 ([R + M] / 2) OR HIGHER.
Mix 2-cycle engine oil with gasoline according to
the instructions on the package.
We strongly recommend the use of 2% (1:50)
Efco two cycle engine oil, which is specifically
formulated for all air-cooled two-stroke engines.
The correct oil / fuel proportions shown in the
table are suitable when using the Efco PROSINT
2 and EUROSINT 2 or an equivalent high-quality
engine oil (JASO specification FD or ISO
specification L-EGD).
GASOLINE
ℓ
1
5
10
15
20
25
CAUTION: DO NOT USE AUTOMOTIVE OIL
OR 2-CYCLE OUTBOARD OIL.
OIL
2% - 50:1
ℓ
(cm 3 )
0,02 (20)
0,10 (100)
0,20 (200)
0,30 (300)
0,40 (400)
0,50 (500)
CAUTION:
- Match your fuel purchases to your
consumption; don't buy more than you
will use in one or two months;
- Store gasoline in a tightly-closed
container in a cool, dry place.
CAUTION - For the mixture, never use a
fuel with an ethanol percentage higher
than 10%; gasohol (mixture of gasoline and
ethanol) up to 10% ethanol or E10 fuel are
acceptable.
When using an Oxygenated Gasoline a good
practice of Fuel Management is necessary.
Gasoline Oxygenated with alcohol readily takes/
up water when it is present; the water may be
condensed out of humid air or be a contaminant
in the fuel system, including tank.
The use of Oxygenated Gasoline may cause the
occurrence of vapor-lock easier.
NOTE - Prepare only the quantity of mixture
required for immediate use; do not leave fuel in
the tank or a container for a long time. Were
commend the use of the additive Emak ADDITIX
2000 code 001000972 if the mixture is to be
stored for 12 months.
Alkylate gasoline
CAUTIONS – Alkylate fuels have different
density than normal fuel. Therefore
engines, set with normal fuel, need different H
jet regulation to avoid critical issues. For this
operation it's necessary turned at a Licensed
Service Dealer.

FILLING THE TANK

WARNING: Follow safety instruction for
fuel handling. Always shut off engine
before fuelling. Never add fuel to a machine
with a running or hot engine. Move at least 3
m from refuelling site before starting engine.
DO NOT SMOKE!
1. Clean surface around fuel cap to prevent
contamination.
2. Loosen fuel cap slowly.
3. Carefully pour fuel mixture into the tank.
Avoid spillage.
4. Prior to replacing the fuel cap, clean and
en
GB
F
D
E
NL
P
GR
TR
CZ
SK
RUS
UK
PL
H
LV
EST
LT
RO
15