Publicidad
Idiomas disponibles
Idiomas disponibles
+40°C
- Max. humidity 95%
DO NOT SLICE:
- frozen food products;
- food products with bones;
- vegetables in general
- any other product not intend-
ed for food use.
Residual risks
The safety ring around the
blade protects the operator
from incidental contact with
the blade although, in order
to allow the sharpening oper-
ations, the protection in the
sharpening area may not en-
tirely eliminate the risk of cut-
ting.
WARNING! during the
!
blade cleaning and sharp-
ening operations, pay extra at-
tention to keep your hands as
far as possible from the unpro-
tected area. Use of protective
gloves is recommended.
INSTALLATION
OF THE MACHINE
If you do not use the stand (op-
tional), install the machine on
a flat, smooth and dry surface
suitable for supporting the
weight of the machine itself
plus the goods to be sliced. The
recommended height of the
worktop is approximately 80
cm. Lift the machine careful-
ly and insert all the feet in the
specific lodgings in the base.
For some models, the front
support feet can be unscrewed
and placed in the desired posi-
tion depending on the depth of
the worktop.
To prevent damage, some mod-
els are packaged separately
from the disassembled fly-
wheel during transport. If the
received machine flywheel is
not assembled, follow these in-
structions:
- insert the flywheel on the
shaft, checking correct cor-
respondence with the fly-
wheel-shaft sleeve holes (Fig.
3-A);
- insert the taper pin in the
sleeve with the tapered end
(smaller diameter) turned to-
ward the sleeve itself (Fig. 3-B);
!
WARNING! If the pin is
correctly positioned, it
will insert almost entirely with-
out being forced.
- hammer down the pin to in-
sert it fully.
The machine must be installed
in the immediate vicinity of an
EEC standard outlet connect-
ed to an electrical supply sys-
tem which is in conformity with
the prevailing regulations for:
- magneto-thermic protection;
- automatic differential switch;
- earthing system.
Before carrying out electrical
hook up verify that the charac-
teristics of the electrical power
supply is in accordance with
those indicated on the machine
information plate.
- Connect the machine to the
power outlet
- Make sure that the sharpen-
ing device protection cover is
positioned correctly (closed).
- Make sure that the emergen-
cy stop button is not pressed.
- Connect the electrical ma-
chine equipment to the mains,
pressing button ON (Fig.2 ,18).
TYPES OF MACHINE STOP
EMERGENCY STOP
For immediate blade stop press
7
the red push-button all the way
down. (Fig. 4-A)
Press the red button all the
way to activate the stop func-
tion for all machine activations.
The blade guard plate will re-
turn to its original position
(closed).
In automatic operating mode,
also check that the carriage
has stopped.
CAUTION! The button
!
(Fig.4-A) maintains its
position when activated (self-
hold).
RESET AFTER AN EMERGEN-
CY STOP
To allow the machine to oper-
ate following an emergency
stop, it is necessary to rotate
the button (Fig.2, 16) in the
clockwise direction and set it
to the raised run consent posi-
tion (Fig. 4-B).
To resume cutting activity in
the preferred mode, follow
the instructions in the chapter
"Use of the slicer".
TEMPORARY STOP
Rotate the flywheel until the
carriage is moved completely
toward the operator (Fig.5),
then stop rotation and stop
the blade by pressing the but-
ton B (Fig. 14, B) LED OFF (Fig.
14, H). The front blade guard
plate will return to the original
closed position.
CAUTION!
!
wheel rotation and, after
approximately 30 seconds, the
front blade guard plate will au-
tomatically return to the origi-
nal position.
Blade movement stops approx-
imately 60 seconds after the
flywheel stops rotating.
To resume cutting after a mo-
mentary stop, press and hold
Stop
fly-
Publicidad
