Cg Tilt Power Accessory; Power Recline; Suretrac; Transit Option And Use - Sunrise Medical Quickie QM-710 Manual De Instrucciones

Q M- 7 10/7 15HD/ 72 0
5. Remain Clear During Power Accessory Operation
Please stay clear of any powered actuator while the compo-
nent is in motion. Sunrise power mechanisms move over
large ranges of travel. Users should be aware of their sur-
roundings while components are in motion.
6. Maximum User Weight
Do not exceed the weight capacity for your specific
chair/seating system configuration. Doing so could result in
premature failure or injury.
7. Latch Mode
While operating any power seating function in latched mode
use caution. In latch mode, powered seating will not stop
until a reverse command is performed or the end of travel is
met.
R. CG TILT POWER ACCESSORY
The powered CG Tilt accessory for this chair has a maximum user
weight capacity of up to 300 lbs for the QM-710 & QM-720,
350 lbs for QM-715 with SEDEO Ergo or 3.7, or 400 lbs for the
QM-715HD and ASAP Seating.
operating the power actuator.
S. POWER RECLINE
Pinch Point
Avoid putting hands or fingers near the power recline mechanism
while in operation.
Weight Capacity
The maximum user weight capacity for the power recline is up to
350 lbs. Exceeding this weight capacity could lead to injury and/or
permanent damage to the equipment.
T. LIFT & LIFT/TILT COMBO
The powered lift and/or lift/tilt modular accessory for this chair
has a maximum user weight capacity of up to 300 lbs. Never
exceed this capacity while operating the powered actuator.
U. SURETRAC
Your chair may be fitted with SureTrac drive tracking. The
electronic controller monitors the connectivity of the drive motors
and in the event of a fault will signal the joystick display with one or
3 error messages:
1. 2001 - M1 Sensor Error - The Power module cannot detect an
Encoder Module connection to M1
2. 3C00 - M2 Sensor Error - The Power module cannot detect an
Encoder Module connection to M2
3. EM Disconnected - The Power module cannot detect an
Encoder Module fitted when the parameter Encoder Fitted to
Yes.
If these errors occur, tracking will be disabled and the chair will continue to
drive but at a reduced speed.
1. Check the motors, cables, and connections to the control system.
2. You may need to reset this fault by switching the control system off and
on again.
3. If the trip is still present after the above checks have been made, then the
Motor or Module may be defective. Consult your Authorized Dealer for
service.
WARNING
Never exceed this capacity while
WARNING
WARNING
VII. WARNINGS: COMPONENTS & OPTIONS
V. TRANSIT OPTION AND USE
Refer also to the "Motor Vehicle Safety" warning section for addi-
tional transit option and motor vehicle warnings.
Transit use does not apply to the QM-715HD.
1. If possible and feasible, the rider should transfer to the
(OEM) original Equipment Manufacturer vehicle seat and use
the vehicle restraint.
2. If the wheelchair is used for transport, it must be used in a
forward-facing seating position.
3. The rider must not weigh more than 300 lbs.
4. Use only with Wheelchair Tie-down and Occupant Restraint
Systems (WTORS) that have been installed in accordance
with the manufacturer's instructions and SAE J2249.
5. Attach WTORS to securement points (A) (B) in accordance
with the manufacturer's instructions and SAE J2249.
6. Attach occupant restraints in accordance with the
manufacturer's instructions and SAE J2249.
7. Ensure hip guides are mounted to lock in place.
8. Use only Wheelchair Tie-down (A, B) and Occupant
Restraint Systems (WTORS) which meet the requirements
of SAE J2249 Recommended Practice– Wheelchair Tie-down
and Occupant Restraint Systems For Use in Motor Vehicles.
Do not use WTORS designed to rely on the wheelchair
structure to transfer occupant restraint loads to the vehicle.
9. The wheelchair has been dynamically tested in a forward-fac-
ing mode for a 30 mph frontal impact test. The wheelchair
must be forward-facing during transport.
10. In order to reduce the potential of injury to vehicle occu-
pants, wheelchair-mounted accessories, such as trays and
respiratory equipment, should be removed and secured sep-
arately.
11. Postural supports and positioning devices should not be
relied on for occupant restraint.
12. Do not alter or substitute wheelchair frame parts, compo-
nents or seating.
13. Sudden stops or impacts can structurally damage your chair.
Chairs involved in such incidents should be replaced.
13
A
WARNING
MK-100158 Rev. F
A