Dealer Service And Adjustment; Dealer Service Introduction; Critical Maintenance Tips; C.CLeaning - Sunrise Medical Quickie QM-710 Manual De Instrucciones

Q M- 7 10/7 15HD/ 72 0
The owner of this chair is responsible for making sure that it has
been setup and adjusted by a trained service professional under the
advice of a Healthcare Professional. Service or adjustments should
only be done with the advice of a Healthcare Professional. Always
use parts and accessories that have been recommended and
approved by Sunrise Medical when servicing this chair. Service and/
or adjustments that require the use of tools, should only be done by
an authorized supplier under the advice of a healthcare professional.
A. DEALER SERVICE INTRODUCTION
1. At least once per year, this chair should have a complete
inspection, safety check, and regular service made by an
authorized dealer.
2. If you have discovered a worn, bent, or damaged part, repair
or replace them with recommended parts before returning
this chair to service..
3. All major maintenance and repair work should be done by
the Authorized Dealer.
4. The tool list at right is essential for any significant repair or
maintenance work.
B. CRITICAL MAINTENANCE TIPS
1. Torque settings:
A torque setting is the optimum tightening which should be made on
a particular fastener. It is important to use proper torque set-tings
where specified. When not specified, torque settings should be set at
a minimum of 60 in-lbs.
NOTE- Maximum torque for motor mount bolts: 80 in-lbs (11Nm).
2. Dealer Service and Adjustment Reference materials:
Go to www.sunrisemedical.com for parts manuals, instruction sheets,
and instructional videos that will aid in the repair of the Quickie/
Zippie Family of wheelchairs.
C. CLEANING
1. Paint Finish
a. Clean the painted surfaces with mild soap or detergent.
b. Protect the paint with a coat of non-abrasive auto wax.
2. Axles and Moving Parts
a. Clean around axles and moving parts with a slightly damp
(not wet) cloth.
b. Wipe off or blow away any fluff, dust or dirt on axles or mov-
ing parts.
c. DO NOT USE 3 in 1 oil, or WD-40 ® for lubrication. Only
use Teflon based Lubricant when working on this wheelchair.
D. ADJUSTMENT NOTES
1. Work Surface For Set-Up:
Use a flat surface, such as a table, to assemble, adjust and check your
chair. This makes the steps easier and helps ensure a correct set-up.
2. Fasteners:
• Many of the screws and bolts on this chair are special high-
strength fasteners and may have special coatings.
• Many nuts are of the Nylock type. They have a plastic insert
to help prevent loosening.
• Only use screws, bolts and nuts provided by Sunrise.
a. Use of improper fasteners may cause the chair to fail.
b. Over- or under-tightened fasteners may fail or cause damage
to chair parts.
c. If bolts or screws become loose, tighten them as soon as you
can. Loose bolts or screws can cause damage to other chair
parts causing them to fail.
WARNING
WARNING
XI. DEALER SERVICE & ADJUSTMENT
3. Washers & Spacers:
• Note the position of washers and spacers before disassembly.
• To avoid damage to the frame, replace all washers and spac-
ers when you reassemble parts.
E. FRONT LIGHTING ADJUSTMENT
Lighting adjustments beyond the ability of the user can result in
serious injury. The front lighting assembly can be adjusted laterally or
vertically to the user's needs. Any adjustment will have a better result if
it is carried out in a dark room or garage, The user should also be in
the chair to verify that the angles and placement for lighting are correct
for their height and abilities.
1. Left, Right, adjustment
a. Using a 3mm hex key, loosen the screw (A) and move the
lighting unit laterally, centering the beam in front of the rider
at the preferred distance.
b. Use the same procecure for the other side of the chair.
c. Retighten the screws.
2. Vertical adjustment
a. Using a 2.5 mm hex key, loosen the set screws (B) on both
sides of the chair and move the lighting units vertically, so
that the surface in front of the chair is well lit at the correct
distance for the user.
NOTE - The measured distance in front of the chair where the beams light
up the riding surface will depend on average speed, and the height
of the user.
b. Tighten the set screws so that the lighting unit won't move
when bumped, or vibrate loose.
c. Make sure the adjustment is correct by allowing the user to
drive with the new setting. Make any additional adjustments
that are necessary.
25
TOOLS YOU WILL NEED
1. Imperial Hex key set
2. Metric Hex key set
3. Imperial Open Wrench set
4. Metric Open Wrench set
5. Torque wrench
6. Imperial Hex bit Socket set
7. Metric Hex bit Socket set
8. Phillips and Flat screwdriver
46
WARNING
A
B
MK-100158 Rev. F
46