List Of Alarms; Manual - Xylem Lowara ResiBoost MMW Manual De Instalación, Funcionamiento, Mantenimiento

en - Original instructions
3. Eliminate the cause of the faults.
4. Press (6) to reset the system (alarms) and the
LED (8) turns off.
5. Press (2) to set AUTOMATIC mode and the
pump starts up if the pressure of the system is
below the set point. This resets the alarms and,
if an alarm is still active, the LED (8) is illuminat-
ed and the pump is still locked. Repeat steps 1–
5.
WARNING:
• Alarm A1 no water and A4 minimum
pressure are not available in manual
mode and it is possible to press (1) to
run the pump.
• Alarms A3, A5, A6, A7, A8, A9 are
available in MANUAL mode and
when an alarm is triggered, the LED
(8) is illuminated and the pump can-
not be started by pressing (1).
• Alarm A2: if the system is in manual
mode and (1) has been pressed to
run the pump, the pump stops and
the LED (8) is illuminated when the
absorbed current exceeds the set val-
ue.

6.1.1 List of alarms

N° Text on Model
the dis-
14
play ( )
A1 WATER MMW
LACK
MTW
MMA
MTA
Causes:
1. No flow of water on the intake side of the pump.
The pump must not run dry because this causes
severe damages.
2. For the MMW and MTW the EL parameter is
enabled and the digital input is open. See
SIC MENU (MB) parameters
3. For the MMA and MTA the EXT.LOW WATER
parameter is enabled and the digital input is
open. See Advanced menu (ME) parameters
page 37
AUTOMATIC mode: Alarm triggered and pump
locked. It is possible to run the pump in manual
mode (2) when the alarm is triggered: press (6),
make sure the LED (8) is off, and press (1). The
pump can be run and primed in this way, but it is im-
portant not to run it on dry for more than 5 seconds.
Solutions:
• Check the working order of the level sensor
(float, minimum pressure switch, optional probe
module panel).
• Check for the presence (level) of water on the in-
take side.
• Check the water pressure on the intake side.
14
MMA, MTA
40
Descrip- Reset
tion
No flow Automat-
of water ic, when
to the the alarm
pump. stops
BA-
on page 35
on
N° Text on Model
the dis-
14
play ( )
A2 OVER MMW
CURR
MTW
MMA
MTA
Troubleshooting: The converter supplies current to
the electric motor above the set rated value. The
converter protects the motor against current over-
load.
Solutions:
• Check the condition of the windings of the elec-
tric motor.
• Check the power consumption of the electric mo-
tor.
• Check the cross-section of the motor's power ca-
ble: this must be suited to the length of the cable
and to the power of the motor.
• Check configuration of the rated current parame-
ter.
• The value of the converter's rated current must
be at least equal to the current value on the data
plate. If the power cable for the motor is longer
than 30 meters, it is advisable to increase the
value by a minimum of 10%.
– para. A models MMW and MTW. See
MENU (MB) parameters
– para. NOM.CURR for models MMA and MTA.
See BASIC MENU (MB) parameters
35.
WARNING:
If the value is not configured correctly,
the motor might NOT be protected
against overload and could suffer irrepar-
able damage.
N° Text on Model
the dis-
14
play ( )
A3 MOTOR MMW
DIS
MTW
MMA
MTA
Descrip- Reset
tion
Overcur- Automat-
rent on ic. A max
the mo- of 4 at-
tor side tempts to
of the start are
electric made at
pump. 2 second
intervals.
Perma-
nent
locking
of the
electric
pump if
the alarm
contin-
ues to be
active af-
ter these
attempts.
BASIC
on page 35.
on page
Descrip- Reset
tion
Electric

Manual.

motor
discon-
nected