Publicidad
Idiomas disponibles
Idiomas disponibles
3.4.2
Accessory set 1 687 016 193
i
To test VDO-CP, the CP1/CP3 accessory set
1 687 010 346 for EPS 708 or the CP3.x accessory
set 1 687 010 182 for EPS 815 and VDO accessory
set 1 687 010 183 are needed in addition to
accessory set 1 687 016 193.
Denomination
1x clamping flange
1x adapter ring
2x hex socket head cap screw M10 x 35
3x hex socket head cap screw M8 x 80
3x hex socket head cap screw M8 x 20
3x hex socket head cap screw M8 x 30
3x hex socket head cap screw M8 x 40
Clamping support parts set
Scope of delivery:
R 1x clamping support
R 1x stud bolt "A" 1 683 180 033
R 1x stud bolt "B" 1 683 180 034
R 1x stud bolt "C" 1 683 180 035
R 2x eccentric pin 1 683 180 014
R 2x washer DIN 125-A13-ST
R 2x hex nut DIN 934-M12
R 2x hex socket head cap screw M8 x 40
Clamping support LION V6 parts set
Scope of delivery:
R 1x clamping support
R 1x clamping plate
R 2x hex socket head cap screw M12 x 35
R 2x eccentric pin 1 683 180 014
R 2x washer DIN 125-A13-ST
R 2x hex nut DIN 934-M12
R 2x hex socket head cap screw M8 x 80
1x intermediate flange
1x intermediate flange
1x intermediate flange
1x intermediate flange
1x intermediate flange
1x quick-release coupling dummy plug
2x screw clamp 10 – 16 mm
1x software "VDO"
1x CD TestData
1x operating instructions
Robert Bosch GmbH
Product description | 1 687 010 193 / 1 687 016 193 | 23
3.5
i
Clamping information for the VDO-CP can be found
in the "EPS945-VDO" software in the "Component
selection-General values" window (see online help).
3.5.1
Clamping flange (Fig. 1, item 1) for fastening VDO-CP
with flange mounting (Fig. 1, item 3) to the clamping
Part number
rail of the EPS 708/EPS 815 with the aid of mounting
1 685 720 369
bracket 1 688 010 129 (optional accessory).
1 680 103 111
–
Using adapter ring 1 680 103 111 (Fig. 1, item 2), it is
–
possible to fasten VDO-CP with a fitting diameter (D) of
–
50 mm to the clamping flange.
–
–
1 688 030 207
1 688 030 209
Fig. 1:
1 Clamping flange 1 685 720 369
1 685 702 109
2 Adapter ring 1 680 103 111
1 685 702 111
3 VDO-CP
1 685 702 113
4 Hex socket head cap screw
1 685 702 115
1 685 702 117
Procedure:
1 684 482 180
1 681 314 078
1. Measure the fitting diameter (D) of the VDO-CP
1 687 005 131
(Fig. 1, item 3). For fitting diameter (D) = 50 mm,
1 687 370 270
insert adapter ring (Fig. 1, item 2) into the
–
clamping flange (Fig. 1, item 1).
2. Push the VDO-CP (Fig. 1, item 3) into the clamping
flange (Fig. 1, item 1).
3. Select the appropriate hole pattern in the clamping
flange by rotating the VDO-CP.
4. Secure the VDO-CP with the appropriate hex socket
head cap screws (Fig. 1, item 4). Tightening torque:
19 – 25 Nm
Component description
Clamping flange 1 685 720 369
1
2
Pump mounting with clamping flange 1 685 720 369
1 689 989 337
en
en
3
4
|
2017-06-15
Publicidad
