Masimo O3 Serie Instrucciones De Uso página 3

Sensores adhesivos rso2 para adultos, sujetos pediátricos y neonatales
Ocultar thumbs Ver también para O3 Serie:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 19
O3® Sensor Series
Adult, Pediatric and Neonatal rSO
Single Patient Use Only
INDICATIONS
The non-invasive Masimo O3® Regional Oximeter System and accessories are indicated for use as an adjunct monitor of regional
hemoglobin oxygen saturation of blood (rSO
The O3 Regional Oximeter is only to be used with Masimo O3  sensors. The use of any other sensor is not supported or
recommended by Masimo and could give erroneous results.
When used with the O3  Adult Sensor, the O3 Regional Oximeter is indicated for measuring absolute and trending regional
hemoglobin oxygen saturation of blood (rSO
When used with the O3 Pediatric Sensor, the O3 Regional Oximeter is indicated for measuring absolute and trending regional
hemoglobin oxygen saturation of blood (rSO
When used with the O3 Neonatal Sensor, the O3 Regional Oximeter is indicated for measuring only trending regional
hemoglobin oxygen saturation of blood (rSO
CONTRAINDICATIONS
The O3 Sensors are contraindicated for patients who exhibit allergic reactions to adhesive tapes.
DESCRIPTION
The rSO
 sensor is a part of the Masimo O3 Regional Oximeter System. The sensor is intended for non-invasive rSO
2
and for single patient use.
WARNINGS, CAUTIONS, AND NOTES
• Periodically check skin integrity according to your institutions patient care protocol or at least every 24 hours.
• The O3 Sensor is intended only as an adjunct in patient assessment. It should not be used as the sole basis for diagnosis or
therapy decisions. It must be used in conjunction with clinical signs and symptoms.
• Always use the O3 Module and O3 Sensor in conjunction with Root. Do not use parts from other systems. Injury to
personnel or equipment damage could occur.
• The O3 Sensor should be free of visible defects, discoloration and damage. If the Sensor appears or is suspected to be
discolored or damaged, discontinue use. Never use a damaged sensor or one with exposed electrical circuitry.
• Do not modify or alter the O3 Sensor in any way. Alteration or modification may affect performance and/or electrical safety.
• Do not use sensors that are wet.
• Do not use the O3 Sensor during magnetic resonance imaging (MRI) or in an MRI environment.
• Do not use the O3 Module and O3 Sensor in the presence of flammable anesthetics or other flammable substance in
combination with air, oxygen-enriched environments, or nitrous oxide to avoid risk of explosion. Refer to the O3 Module
Operator's Manual for additional information.
• Do not place electrodes between the surgical site and the electro-surgical return electrode. Doing so increases the risk of
burns in case of a defect in the electro-surgical return electrode.
• As with all medical equipment, carefully route patient cabling to reduce the possibility of patient entanglement or
strangulation.
• Avoid placing the sensor on any extremity with an arterial catheter or blood pressure cuff.
• Do not use tape to secure the sensor to the site; this can restrict blood flow and cause inaccurate readings. Use of additional
tape can cause skin damage and/or pressure necrosis or damage the sensor.
• The site must be checked frequently or per clinical protocol to minimize the risk of skin irritation and to ensure adequate
circulation, skin integrity and correct optical alignment.
• Exercise extreme caution with poorly perfused patients; skin erosion and pressure necrosis can be caused when the sensor
is not frequently moved. Assess site as frequently as every one (1) hour with poorly perfused patients and move the sensor
if there are signs of tissue ischemia.
• For patients experiencing complete bilateral External Carotid Artery (ECA) occlusion, rSO
than expected.
WARNING: Optical measurements (rSO
• Improper sensor application or use of incorrect sensor.
• Intravascular dyes such as indocyanine green or methylene blue or externally applied coloring (such as indelible ink).
• Venous congestion and pooled blood under the skin.
• Moisture, birthmarks, skin discoloration or foreign objects (e.g. metal plate) in the light path.
• Elevated level of total bilirubin.
• A physiological condition that may affect vasomotor tone or changes in vasomotor tone.
• Excessive ambient light, high intensity light, or direct sunlight.
2
D I R E C T I O N S F O R U S E
LATEX
Not made with natural rubber latex
) in the cerebral region under the sensors in patients in healthcare environments.
2
PCX-2108A
02/13
) in adults ≥ 40 kg.
2
) in pediatrics ≥ 5 kg and < 40 kg.
2
) in neonates < 10 kg.
2
) can be affected by the following:
2
Adhesive Sensors
3
NON
Non-sterile
STERILE
LATEX
95%
%
5%
 measurements
2
measurements may be lower
10329C-eIFU-0919
+70 C
-40 C
+1060 hPa - +500 hPa
795 mmHg - 375 mmHg
5%-95% RH

Publicidad

Tabla de contenido
loading

Tabla de contenido