Anest Iwata DDP 120 B.TE Manual De Instrucciones página 69

DPS-70 C - DPS-70 CN DIAPHRAGM PUMPS
EN
4.5 PIECES CONTAINED IN THE PACKAGE
ASSEMBLY on STAND
PR-5BL
Drain hose set
*Cart set
-
Supply lid
-
Hose band
3
Suction hose set with filter
1
Dip tube with filter
-
**Gravity hopper set
-
*CART SET
AXLE 1
"U" BOLT _ HEX. NUT 2 + 4
SNAP PIN 4
4
WASHERS
2
SOLID TIRES
HANDLE 1
HEX. NUT (M8) 1
BOLT WITH HEX. HOLE (M8) 1
HEX. NUT (M6) 1
BOLT WITH HEX. HOLE (M6) 1
5. PRODUCT IDENTIFICATION
5.1 PLATE DATA
The manufacturer's identification plate is applied on the diaphragm pump (see picture below).
It must not be removed at all, even if the equipment is resold. For any communication with the manufacturer always mention
the serial number written on the plate itself.
5.2 COMPLIANCE TO THE STANDARD
All the units are conceived in compliance with the applicable Essential Safety Requirements of the Machinery Directive
2006/42/EC. The units are also designed and manufactured in compliance with the Essential Safety Requirements (ESR) of
Annex II of Directive "ATEX" 2014/34/EU and they comply with the following classification:
• Equipment group : II
• Category: Gas 2G (Suitable for use in zones 1 and 2)
• Max. surface temperature: temperature class T6
• X marking : Any static electricity discharge from the pump is to be diverted to the ground through the
grounding wire which is included in this product.
6
on CART ALL MODEL on TANK MOUNT on WALL MOUNT
1
1
1 -
- 1
3 -
1 -
- 1
1 -
**HOPPER SET
HOPPER 1
"U" HOSE 1
DPS-70 C - DPS-70 CN DIAPHRAGM PUMPS
6. TECHNICAL SPECIFICATIONS
VERSION
PUMP VERSION
Paint Passages
-
Air Working Pressure range
-
Max. Fluid Working Pressure
3
Air Inlet
1
Fluid Outlet
-
Fluid Inlet
-
Paint Delivery at 30 cyc/min
Paint Delivery at 200 cyc/min
Paint Viscosity
Working Temperature
Compressor (required power)
Noise Level
PERFORMANCE CURVE
* 0.3/0.5/0.7 MPa in graph shows air pressure
* Test by turpentine
6.1 DIMENSIONS AND WEIGHT
VERSION
STAND TYPE
TANK MOUNT TYPE
CART TYPE
WALL MOUNT TYPE
CART TYPE WITH HOPPER
DPS-70 C.TE
DDP-70B
Aluminium
1.5~7 bar (22~100 psi)
7 bar (100 psi)
G 1/4"
G 3/8"
G 1/4"
0.6 lt./min
6 lt./min
60sec/Ford#4
5~40°C
0.4~0.75 kW
66 dB(A)
MODELS DIMENSIONS (mm)
DPS -701 C
410 x 358 x 700
DPS -701 CN
DPS -702 C
357 x 312 x 683
DPS -702 CN
DPS -703 C
439 x 452 x 868
DPS -703 CN
DPS -704 C
364 x 214 x 428
DPS -704 CN
DPS -7036 C
573 x 555 x 868
DPS -7036 CN
EN
DPS-70 CN.TE
DDP-70 BN
Stainless Steel
WEIGHT (Kg)
6.0
7.4
5.1
6.5
8.5
9.9
5.0
7.1
8.5
9.9
7