Introduction; Guidelines For Reading The Manual; Storing The Manual; Method For Updating The Instruction Manual - Wega URBAN Manual De Uso Y Mantenimiento

1.

INTRODUCTION

Please read this manual in its entirety before using
the device, in order to optimise machine performance
and operate it safely.
The espresso co ee machine you have purchased
has been designed and manufactured with innovative
methods and technologies which ensure long lasting
quality and reliability.
This Manual is the guide that will enable you to learn
about the bene ts of choosing our brand. You will nd
information on how to get the best out of your appliance,
how to keep it running e ciently and what you should
do if problems occur.
Keep this Manual in a safe place. If you displace this
Manual, please contact the Manufacturer to receive a
replacement copy.
Before using the machine, carefully read and follow the
instructions contained in this publication. Keep this manual
and all attached publications in an accessible and secure place.
This document assumes that the machine is installed in a location
where the current work safety and hygiene standards are observed.
Instructions, drawings and documentation contained
in this Manual are technical and con dential. They are
the sole property of the Manufacturer and may not be
reproduced in any way, whether in wholr or in part.
The Manufacturer reserves the right to make any
improvements and/or modi cations to the product. We
guarantee that this Manual re ects the technical state of
the appliance at the time it was released to the market.
We take this opportunity to invite customers to make
any proposals to improve the product or its Manual.
Guidelines for reading the
1.1
Manual
This Manual is divided into separate chapters. The chapter order is linked
to the temporal logic of the life of the machine.
Terms, abbreviations and pictograms are used to facilitate the immediate
understanding of the text.
This Manual consists of cover, index and a series of chapters. Each chapter
is sequentially numbered. The page number is shown in the footer.
The rst page displays the machine identi cation data and the last page
displays the date and revision of the Instruction Manual.
ABBREVIATIONS
Sec. = Section
Chp. = Chapter
Par. =
Paragraph
Pg. = Page
Fig. = Figure
Tab. = Table
UNITS OF MEASUREMENT
The units of measurement are those provided by the International System
(SI).
USER Manual
PICT OGRAMS
Descriptions preceded by these symbols contain very important informa-
tion/requirements, particularly in regards to safety. Failure to comply with
these may result in:
• hazards to the operator's safety;
• injury, including serious injury, to users (in some cases, even death);
• loss of warranty;
• mMnufacturer's waiver of liability.
DANGER symbol used when there is a risk of permanent serious
injury that requires hospitalisation, or in extreme cases, cause
death.
CAUTION symbol used when there is a risk of minor injury that
could require medical attention.
WARNING symbol used when there is a risk of minor injury that
could be treated with rst-aid or similar measures.
NOTE symbol used to provide important information about the
topic.

Storing the Manual

1.2
The Instruction Manual must be stored in a safe place and accompany the
machine in all ownership transfers.
The manual should be stored, handled with care with clean hands and
not placed on dirty surfaces. Do not remove, tear or arbitrarily modify any
of its parts.
The manual must be stored away from moisture and heat, and in close
proximity to the machine it refers to.
On the user's request, the Manufacturer can provide additional copies of
the Instruction Manual.
Method for updating the
1.3
Instruction Manual
The Manufacturer reserves the right to modify and make improvements
to the machine without providing notice or updating the Manual that has
already been received by the user.
Moreover, when substantial changes made to the machine require the
modi cation of one or more chapters of the Instruction Manual, the Manu-
facturer will send users the chapters a ected by the changes or a revision of
the entire Manual.
It is the users' responsibility to replace the old document with the new
revision.
The Manufacturer is responsible for the Italian content. Translations cannot
be fully veri ed; therefore, in the event of inconsistency, users can refer to the
Italian version or if necessary, contact the Manufacturer who will make the
appropriate changes.
47 272
of