Maintenance And Storage; Transportation And Handling; Machine Assembly - GGP ITALY SBC 425 H Manual De Instrucciones

cautions to ensure your own safety, especially
on slopes or on bumpy, slippery or unstable
ground.
– W ork along the contour on slopes, never when
walking up or down and always keep downhill
of the cutting device.
4) Make sure the machine is securely locked
when you start the engine:
– s tart the engine in an area at least 3 metres
from where you refuelled;
– c heck that there is nobody within at least 15
metres of the machine's range of action or at
least 30 metres for heavier cutting;
– d o not direct the silencer and therefore the ex-
haust fumes towards inflammable materials.
5) Do not change the engine settings or over-
speed the engine.
6) Do not strain the machine too much and do
not use a small machine for heavy-duty works;
if you use the right machine, you will reduce the
risk of hazards and improve the quality of your
work.
7) Check that when the machine is running idle,
there is no movement of the cutting device and,
after pressing the throttle trigger, the engine
quickly returns to minimum speed.
8) Ensure that the blade does not come into
violent contact with foreign bodies and beware
of the possibility of material being thrown up by
the blades.
9) Always keep the machine connected to the
harness when working.
10) Stop the engine:
– w henever you leave the machine unattended;
– b efore refuelling;
– w hen moving between work areas.
11) Stop the engine and disconnect the spark
plug cable:
– b efore checking, cleaning or working on the
machine;
– a fter striking a foreign object. Inspect the ma-
chine for damage and make repairs before re-
starting and operating the machine;
- if the machine begins to abnormally vibrate: im-
mediately look for the cause of the vibrations and
have it checked at a Specialised Centre).
– w hen the machine is not in use.
WARNING! Stop the engine immediately if
the blade stops during work. Always be-
ware of a kickback, which could occur if a
blade encounters a solid object (logs, roots,
branches, stones, etc.). Do not touch the
ground with the blade. Kickbacks cause
blade recoils that are difficult to control,
causing loss of control of the machine, jeop-
ardising operator safety and causing dam-
age to the machine itself.
D) MAINTENANCE AND STORAGE
All manuals and user guides at all-guides.com
1) Keep all nuts and screws tight to be sure the
machine is always in safe working condition.
Routine maintenance is essential for safety and
for maintaining a high performance level.
2) Do not store the machine with fuel in the tank
in an area where the fuel vapours could reach
an open flame, a spark or a strong heat source.
3) Allow the engine to cool down before storing
the machine in any enclosure.
4) To reduce fire hazards, keep the engine, ex-
haust silencer and fuel storage area free from
sawdust, branches, leaves, or excessive grease;
never leave containers with the cut debris inside
the storage area.
5) If the fuel tank has to be emptied, this should
be done outdoors once the engine has cooled
down.
6) Always wear protective gloves when handling
the cutting device.
7) Before putting the machine away, check you
have removed wrenches or tools used for main-
tenance.
8) Store the machine out of the reach of chil-
dren!
1) Whenever the machine is to be handled or
transported you must:
– t urn off the engine, wait for the cutting device
– fi t the cutting device guard;
– o nly hold the machine using the handgrips and
2) When using a vehicle to transport the ma-
chine, position it so that it can cause no danger
to persons and fasten it firmly in place to prevent
it from tipping over, which may cause damage or
fuel spillage.
NOTE - The figures mentioned in the text are
found on page 4 and following of this man-
ual.
IMPORTANT The machine is supplied with
some of the components disassembled and the
fuel tank empty.
tive gloves to handle the cutting devices.
12
E) TRANSPORTATION AND HANDLING
to stop and disconnect the spark plug cap;
position the cutting device in the opposite di-
rection to that used during operations.
OPERATING INSTRUCTIONS

1. MACHINE ASSEMBLY

WARNING! Always wear strong protec-