Electric Supply; Installation And First-Time Start-Up; Operation; Controls - Rancilio EPOCA Serie Instrucciones Originales

6.1.2. Electric supply

The machine is supplied ready for connection
according to the required electrical specifi-
cations.
Before connecting the machine ensure that the plate
details (fig. 1) comply with those of the electric distri-
bution network.
The electrical connection cable must be directly con-
nected to the connection provided according to current
legislation. Ensure that the earthing system is efficient
and in compliance with current legal requirements.
The earthing system and the lightening protection
system must be realized in accordance with the
provisions of current legislation.
For the supply network use a cable in compliance with
standards with protective conductor (earthing wire).
For single phase power supply use a cable with 3
conductors (phase + neutral + earth).
In both cases it is necessary to provide an automatic
differential switch (Fig. 6) at the start of the power
cable, complete with magnetic release elements in
accordance with the identification plate details (Fig. 1).
The contacts must have an opening of equal or over 3
mm and with dispersed current protection of 30 mA.
Remember that each machine must be fitted with its
own safety elements.
WARNING:
Should the power supply cable be damaged
it is to be replaced by the manufacturer or by
its technical assistance service or by person
with equivalent qualification, in order to pre-
vent any risks.
6.2. Installation and first-time start-
up
● Position the machine unit onto the horizon-
tal surface provided for that purpose and adjust
the base feet to ensure that the machine is stable
and that vibrations are limited.
Before connecting, thoroughly wash the mains water
pipes:
● Leave the water supply taps running at full pres-
sure for several minutes.
● Connect to the mains water supply.
● Connect the machine up to the power supply
mains.
Thoroughly wash all the water pipes of the machine:
● Leave the water supply taps running at full pres-
sure.
● Switch on main switch 1: wait until the boiler fills
up to the level set.
● Switch on main switch 2 to begin heating the water
in the boiler.
● Once standard machine work conditions have been
reached with the machine in "ready for operation"
mode, switch the machine off and empty all the wa-
ter filled into the water circuit the first time, thereby
eliminating any possible initial impurities.
● Fill the machine up with water again and set it into
standard operation mode.
● Once the "ready for operation" status is reached:
- Connect the filter-holders to the dispenser units
(without coffee); operate each group head in
order to allow the water to escape for about one
minute.
- Dispense hot water until at least 2 liters of water
have been dispensed.
- Open each steam dispensing point for 1 whole
minute.
Once installation is terminated, the installa-
tion technician MUST issue an installation
report.
ATTENTION
Please be informed that in order to avoid
pressure falls during the boiler filling we fitted
into the filling solenoid valve a restription Ø
1.25 mm.
If, during the installation, the machino get
in security mode (the on/off selection on the
touch pad will flash) reset the machine using
the main switch.

7. OPERATION

7.1. Controls (Fig.6 - 6A)
1 Main switch.
Two-position switch with led.
Turn on the switch, led on, the machine is turned
(apart from the boiler) and the pump is turned on
to fill the boiler;
2 Boiler resistance switch.
Two-position switch with led.
On activating the switch, the led comes on, and
power is supplied to the resistance for the boiler
water.
3 Coffee dispenser switch (mod. S - S TANK)
On pressing the button, continuous coffee dispen-
sing begins and the led comes on.
On re-pressing the switch, the coffee delivery stops
and the led goes out.
4 Electronic coffee delivery button panel.(mod.
E).
Five buttons with relative led:
A
Press the button for a second, led on, release
button; a small coffee is dispensed.
The led turns off and dispensing ceases.
B Press the button for a second, led on, release
the button; two small coffees ar dispensed from
the same unit.
The led turns off and dispensing ceases.
C
Press the button for a second, led on, release
the button; a big cup of coffee is dispensed.
The led turns off and dispensing ceases.
D Press the button for a second, led on, release
the button; two big cups of coffee are dispensed
from the same unit.
The led turns off and dispensing ceases.
59