Arktic SLUSH MACHINE 2X12L Manual Del Usuario página 14

c) Start operating the machine:
GB
(Control panel : Fig.2 on page 3)
Each bowl is controlled independently.
• First, connect the power plug to a suitable electrical power
outlet.
• Next, press (21) to switch ON the machine. Press and hold
(21) for 3 seconds to switch to STANDBY mode of the machine
when not use. (Fig.8 on page 5).
• Then, press the corresponding bowl button (12).
And press consecutively to select the working mode. There
are 3 working modes: Granita (18) , juice (19) or OFF (20). It
will be displayed in sequence and the corresponding icon will
be lighted.
I). To serve with Granita
(Fig.9 on page 5)
• Press the corresponding bowl button (12).
• Next, press consecutively to select Granita mode, (18) will be
lighted.
• Then, press "+" or "-" consecutively to adjust the hardness.
The level in between from 1 (Soft with much water content) to
7 (Hard with less water content).
II). To serve with cold drinks
(Fig.10 on page 5)
• Press the corresponding bowl button (12) until (19) lights up.
• Enter to juice temperature setting mode by long pressing (22)
until "PR" is blinking on the display.
• Press (22) again to select bowl 1(F1) or 2(F2) until "F1" or "F2"
is shown on the temperature display.
• Press left panel (17) to adjust the temperature from 1°C ~ 7°C.
The temperature will be set successfully. After flashing 15
times without any operation, the display will return to normal.
NOTICE:
• Current temperature is showing on display as normal.
• Press (14) and (16) at the same time for restoring to default
temperature( 2°C ).
• Display shows "PR" / "F1" / "F2" : Juice temperature setting
mode / bowl 1 / bowl 2. The mode will become invalid after
flashing 15 times without any operation and display will switch
back to normal.
• Only left panel (17) can be operated (for both bowl 1 and 2)
within juice temperature setting model.
III). To stop working
• Press the corresponding bowl button (12).
• Next, press consecutively until OFF mode, (20) will be lighted.
Then, it would stop stirring and refrigerating.
d) To simply clean the corresponding bowl:
• Press and hold the corresponding bowl button (12) for about
6 seconds.
• The corresponding bowl valve will be fully open for cleaning
about 3 minutes. During this mode, the control display will
show "°C".
ATTENTION! Under this mode, the electronic expansion valve of
the corresponding bowl will open. But the auger still stirring for
cleaning. Please fill with warm and clean water into the bowl
not exceeding the "MAXIMUM LEVEL". Do not put your hand in-
side.
Switch OFF the machine and unplug it for thorough cleaning or
14
sanitization to the machine.
e) Dispensing granita
(Fig.11 on page 6)
• To dispense the food product, pull the tap lever.
NOTE: Regularly check the temperature of the beverages in the
bowl (2). Keep on the machine running when there is any
food inside the bowl.
If the machine is not continuously operated, it is necessary to
dispose of the small amount from the tap area first before serv-
ing for the customer.
Cleaning & Maintenance
ATTENTION! Always disconnect the appliance from the elec-
trical mains and cool down before storage, cleaning & main-
tenance.
Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
Before performing any cleaning and maintenance operation
on the machine, wear the personal protective clothes such as
gloves, protective glasses, etc.
Cleaning
• Clean the cooled exterior surface with a slightly damp cloth or
sponge with some mild soap solution.
• No any components can be cleaned in the dishwasher.
• No any components can be dried in the microwave oven.
• Never use abrasive sponges or detergents, steel wool or
metallic utensils to clean the interior or exterior parts of the
appliance.
• The bowl should be cleaned and sanitized at least once a day.
• Cleaning and sanitization are operations that require care and
on a regular basis to guarantee the quality of the beverages
dispensed and for the hygiene purpose.
• WARNING! Do not plug in or switch ON the machine during
the cleaning and maintenance operation.
• Lift the upper part of the protector and remove it for cleaning
and maintenance operation. Once finished, fit the part in the
machine again. (Fig.12 on page 6).
a) Emptying the bowls
• Before a bowl may be cleaned, it must be emptied all the food
ingredient inside the bowl first.
b) Disassembly the dispensing tap:
• Ensure all the beverage are emptied inside the bowl.
• Disassembly the tap before removing the bowl.
• Remove the pin (F) to release all the other parts. (Fig.13 on
page 6)
• Use clean and warm water to wash the parts. (Fig.14 on page
6)
c) Remove the bowl and the lid:
• To remove the bowl lid (1) of the bowl (2) first, follow these
instructions & see Fig.15 on page 6.
1) Lift the rear part of the lid;
2) Extract the bowl lid (1) from the retainer placed at the
front side.
• Then, raise the front part of the bowl to release it.
• Next, remove the bowl from its position by pushing slightly at