Heating A Beverage; Warming A Beverage; For Pu - Me - Plus Models; For Plus + Ts Models - Promac GREEN Instrucciones Originales

● Open the steam tap 7 (fig. 7) and lower the con-
tainer until the steam spray skims the surface of
the milk and emulsifies it.
● Close the steam tap and pour the milk into the cup
containing the espresso coffee.
Immediately after carrying out this operation,
clean the spout with a sponge or a clean
cloth so that the milk does not dry on it. Be
careful as the the spout is hot and may burn
your hand.
Delivery time must not exceed 5 minutes.

8.3. Heating a beverage

8.3.1. For PU - ME - PLUS models

●Immerse the steam spout into the liquid to be
heated;
● Gradually turn on the steam tap 7 (Fig.7); the
steam that bursts in the liquid heats it to the desired
temperature.
● Turn off the steam tap when the desired tempera-
ture has been reached.
Immediately after carrying out this operation,
clean the spout with a sponge or clean cloth.
Be careful as the spout is hot and may burn
your hand.

8.3.2. For PLUS + TS models

This machine version is equipped with a steam
dispenser nozzle featuring a temperature probe
that is used to automatically heat up liquids (milk,
for example). Pressing the corresponding key, the
vapour supply electro-valve is activated until the
temperature programme is reached or until manual
interruption of supply.
To heat liquids, proceed as follows:
● Immerse the vapour spout with probe (TS device)
in the liquid to be heated.
● Press key 6 on the pushbutton panel beforehand
(see technical programming), the vapour will start
to come out, heating the liquid by conduction until
the programmed temperature is reached. The
word steam is displayed. At this stage it is possi-
ble to interrupt the function by pressing the same
key or continuing the output of steam at a higher
temperature than programmed by keeping the key
pressed.
N.B.: As the steam spout is an optional, the
ON key and relative pushbutton panel are to
be set in technical level programming.
All manuals and user guides at all-guides.com

8.4. Preparing tea, camomile, etc.

● Place the jug under the hot water spout 4 (Fig.3)
and use the delivery control according to the mo-
del (Fig. 7). When the desired quantity has been
obtained, close the tap (dispensing is automatically
halted according to the quantity set for models
GREEN ME).
During the delivery of hot water electronically do-
sed, delivery can be interrupted by pressing button
6 (Fig. 7).
To adjust the doses, see Paragraph 9.
● Add the desired product.
When purified water is used, these beverages often
assume a darker colour. Should the user prefer
a lighter coloured drink, draw fresh water from an
ordinary tap and proceed with the heating phase as
described in point 8.2.

9. PROGRAMMING

9.1. User programming

9.1.1. For ME: COMPACT - PLUS models
The doses of coffee and hot water dispensed can
be adjusted on the electronically controlled models.
● Place the filter-holder with the ground coffee under
the unit to be programmed and the cup (or cups)
under the corresponding spouts;
● Keep the E key (Fig. 7) of the keyboard located
onto the first group on the left hand side pressed for
5 seconds. The flashing leds of the E keys indicate
the enabling of the programming phase.
● Within 5 seconds press the appropriate key (A-
B-C-D) and visually check the delivery; when the
quantity delivered corresponds to the desired
amount, press the same key again; delivery cea-
ses and the volume of the dose is automatically
memorized.
● Follow the same procedure if any other adjustmen-
ts are possibly required. This procedure is also
valid for the hot water dispensing keys (2 different
doses) (Fig. 7).
Do not make adjustments to units that do not
have a filter-holder with coffee and correspon-
ding cups.
The adjustment made to the first unit on the left
also applies to the other units. If you wish to obtain
different doses from the other units, the unit on the
left must first be adjusted, followed step-by-step by
the others.
At the end of the programming phase wait at least 5
seconds before beginning the selections.
The data memorised is permanently stored within
the memory even in the case of complete absence
of electric power.
81