Basic Settings; Setting Dmx Channels; Assigning Movement Channels - Leuchtkraft DMX-3216 Manual De Instrucciones

4.2 Basic settings

4.2.1 Setting DMX channels

For separate control of all DMX units connected
to the light controller, each unit must have its
own start address . The 512 DMX channels of
the DMX-3216 are divided into equally sized
address sections for 16 units, each with up to
32 DMX channels . Consequently, the following
start addresses will have to be set at the individ-
ual units:
Unit Start address
1
2
3
4
5
6
7
8

4.2.2 Assigning movement channels

To make sure that units with controllable move-
ments (e . g . moving head, scanner) allow these
movements to be controlled by the jog wheels
(19, 22) and to make sure that the movement
patterns (MOVEMENT) of the controller work cor-
rectly, assign the jog wheels to the appropriate
PAN and TILT channels of the respective unit . In
addition, the two movement directions can be
reversed, if necessary .
1) Use the POWER switch (33) to switch on the
controller .
2) Keep the button PROGRAM / REC (10) pressed
for 3 s . The LED next to the button will start to
flash to indicate that the programming mode
has been activated .
3) Press the buttons FINE (18) and MODE (20)
at the same time . The LED ASSIGN (9) will
light up and
display (11) .
4) Use the number buttons (17) to select the
number of the unit for which the assignment
is to be made . It is possible to select multiple
units at the same time if they are to be set
identically . When a unit has been selected, the
LED above the appropriate number button will
20
Unit Start address
1 9
33 10
65 11
97 12
129 13
161 14
193 15
225 16
will appear on the
ASS00 00
light up . To deselect a unit, press its number
button again .
The display will indicate the current assign-
ment for the unit selected, e . g .
for PAN = channel 2 and TILT = channel 4 . If
no assignment has been made of if the as-
signment has been deleted,
appear on the display .
5) Use the button  or  (13) to define if the
pan movement (PAN) or the tilt movement
(TILT) is to be assigned . The LED above the
appropriate jog wheel (19, 22) will light up to
indicate the current selection .
257
6) Keep the button MODE pressed and also press
289
the button (1) above the control for the cor-
321
responding channel . Since a unit can have up
353
to 32 channels, four channels are assigned to
385
each button (levels A – D) [
417
above the sliders] . The LEDs A – D (2) indicate
449
the current level . Use the button PAGE (3) to
481
switch to another level .
All LEDs will flash briefly to confirm the as-
signment; the number of the channel assigned
will appear on the display .
Repeat steps 5 and 6 for the other movement
direction .
7) To delete the assignments, press the buttons
MODE and DEL (21) at the same time . All
LEDs will flash briefly to confirm the deletion;
ASS00 00
8) To switch to the direction reversal option, press
the buttons FINE and MODE at the same time .
The LED REVERSE (9) will light up and the dis-
play will indicate the current channel reversal
of the unit selected, e . g .
channel 2 is reversed, the TILT channel is not
reversed .
9) Use the button  or  to define if the pan
movement (PAN) or the tilt movement (TILT) is
to be reversed . The LED above the appropriate
jog wheel will light up to indicate the current
selection .
10) Keep the button MODE pressed and also press
the button (1) above the control for the corre-
sponding channel .
All LEDs will flash briefly to confirm the as-
signment; the number of the channel reversed
will appear on the display .
ASS00 00
lettering right
☞
will appear on the display .
RES02 00
ASS02 04
will
= PAN