Publicidad
Idiomas disponibles
Idiomas disponibles
GENERAL POWER TOOL SAFETY WARNINGS
e. Maintain power tools and
parts and any other condition that may affect the power tool's
tool repaired before
f. Keep cutting tools sharp and
bind and are easier to
g. Use the power tool, accessories and tools bits
account the working conditions and the work to be
from those intended could result in a hazardous
h. Keep Handles and grasping surfaces dry, clean and free from oil and
surfaces do not allow for safe handling and control of the tool in unexpected
5.
Service
a. Have your power tool serviced by a qualified repair person using only identical replacement
will ensure that the safety of the power tool is
SAFETY INSTRUCTIONS FOR MITER SAWS
1.
a. Miter saws are intended to cut wood or wood-like products, they cannot be used with abrasive cut-off
wheels for cutting ferrous material such as bars, rods, studs,
the lower guard to
b. Use clamps to support the workpiece whenever
always keep your hand at least 100mm from either side of the saw
pieces that are too small to be securely clamped or held by
blade, there is an increased risk of injury from blade
c. The workpiece must be stationary and clamped or held against both the fence and the
the workpiece into the blade or cut "freehand" in any
at high speeds, causing
d. Push the saw through the
the saw head and pull it out over the workpiece without cutting, start the motor, press the saw head
down and push the saw through the
climb on top of the workpiece and violently throw the blade assembly towards the
e. Never cross your hand over the intended line of cutting either in front or behind the saw
Supporting the workpiece "cross handed"
vice versa is very
f. Do not reach behind the fence with either hand closer than 4 inches from either side of the saw blade, to
remove wood scraps, or for any other reason while the blade is
blade to your hand may not be obvious and you may be seriously
g. Inspect your workpiece before
bowed face toward the
and table along the line of the
spinning saw blade while
h. Do not use the saw until the table is clear of all tools, wood scraps, etc., except for the
debris or loose pieces of wood or other objects that contact the revolving blade can be thrown with high
i. Cut only one workpiece at a
bind on the blade or shift during
j. Ensure the miter saw is mounted or placed on a level, firm work surface before
surface reduces the risk of the miter saw becoming
k. Plan your
work.
is set correctly to support the workpiece and will not interfere with the blade or the guarding system.
Without turning the tool "ON" and with no workpiece on the table, move the saw blade through a complete simulated
cut to assure there will be no interference or danger of cutting the fence.
accessories.
Check for misalignment or binding of moving parts, breakage of
use.
Many accidents are caused by poorly maintained power
clean.
Properly maintained cutting tools with sharp cutting edges are less likely to
control.
jam.
Sparks from abrasive cutting will burn the lower guard, the kerf insert and other plastic
injury.
workpiece.
Do not pull the saw through the
workpiece.
i.e.
dangerous.
cutting.
fence.
Always make certain that there is no gap between the workpiece, fence
cut.
Bent or warped workpieces can twist or shift and may cause binding on the
cutting.
There should be no nails or foreign objects in the
time.
Stacked multiple workpieces cannot be adequately clamped or braced and may
cutting.
Every time you change the bevel or miter angle setting, make sure the adjustable fence
operation.
etc.
in accordance with these instructions, taking into
performed.
Use of the power tool for operations different
situation.
maintained.
etc.
possible.
If supporting the workplace by hand, you must
hand.
contact.
way.
Unrestrained or moving workpieces could be thrown
Cutting on the pull stroke is likely to cause the saw blade to
holding the workpiece to the right of the saw blade with your left hand or
spinning.
injured.
If the workpiece is bowed or warped, clamp it with the outside
unstable.
8
If damaged, have the power
tools.
grease.
Slippery handles and grasping
situations.
Abrasive dust causes moving parts such as
blade.
Do not use this saw to cut
If your hand is placed too close to the saw
table.
workpiece.
To make a cut, raise
operator.
The proximity of the spinning saw
workpiece.
workpiece.
use.
A level and firm work
parts.
This
parts.
Do not feed
blade.
Small
speed.
Publicidad
