Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
-
I
N
-
I
N
-
I
N
type of defrost for manual defrost from keyboard
d8
(0 = by resistance, 1 = by hot gas, 2 = air)
dE
defrost interval count: 0= actual hours; 1=hours comp.
A0
alarm hysteresis (differential)
A1
Alarm for minimum relative to positive conservation setpoint (0 = excluded)
A2
Alarm for maximum relative to positive conservation setpoint (0 = excluded)
A3
Alarm for minimum relative to negative conservation setpoint (0 = excluded)
A4
Alarm for maximum relative to negative conservation setpoint (0 = excluded)
A5
alarm exclusion time for beginning conservation phase temperature
alarm exclusion time for conservation temperature post evaporation fan stop
A6
(if d1 = 0 or 1)
A7
delay time for alarm acquisition (for AH and AL)
A8
inhibition blast chill / freezing cycle temperature (chamber or centre probe)
A9
modalities for alarm buzzer activation: 0 = always; 1 = temporised
AA
limit time for alarm buzzer acoustic signal (only if A9 = 1)
chamber temperature threshold in which the evaporator fan is turned off in blast
F0
chill / freezing
evaporator temperature threshold over which the evaporator fan is turned off in
F1
conservation (only if /5 = 0)
F2
evaporator fan hysteresis in conservation (relative to F1, only if /5 = 0)
Evaporator fan state in conservation with compressor off (0 = fans not
F3
correlated to the compressor state, 1 = fans OFF if compressor OFF)
evap. vent. operation during defrost and dripping
F4
(0= OFF, 1= ON, 2= determ. with F3)
F5
evaporator fan stop after dripping
P0
Sampling time in blast chill / freezing (see also parameter P6)
P1
Sampling time in positive / negative conservation (see also parameter P6)
Selection of temperature probe to be printed
2 = chamber and evaporator probe (if present), 4 = large pin probe,
P2
5 = chamber probe and large pin probe, 6 = chamber probe, large pin probe
and evaporator probe (if present)]
P3
Payslip heading selection (0 =excluded, 1 = Blast Chill, 2 = Blast Chill Freezer)
P4
Equipment identification number printing enable (0 = no, 1= yes)
Selection of language for payslip heading
P5
(1 = Italian, 2 = English, 3 = French, 4 = Spanish, 5 = German)
P6
Selection of unit of measure for sampling time (1 = minutes, 2 =hours)
P7
Configuration parameters printing enable (0 = disabled)
L1
Instrument address (date detected in printing phase if P4 = 1)
L2
Serial port management (o = not utilised, 1 = print, 2 = supervision in BusMod))
L3
Baud Rate data transmiss. (1=2400, 2=4800, 3=9600, 4=18200)
L4
Transmission control mode (0 = no parity, 1 = odd, 2 = even)
CHANGING PARAMETERS
Push up and down buttons for 4 seconds to enter into parameter configuration.
Access password is requested.
Use the keys up and down to select the password "65"
Push
The first parameter is displayed.
18
S
T
A
L
L
A
T
S
T
A
L
L
A
T
S
T
A
L
L
A
T
ALARMS
EVAPORATOR FAN ADJUSTMENT
[0 = none, 1 = chamber probe,
COMMUNICATIONS MANAGEMENT
on/sby/enter
to confirm your choice.
button
I
O
N
M
A
N
U
I
O
N
M
A
N
I
O
N
M
A
N
PRINT
A
L
-
U
A
L
-
U
A
L
-
2
0
0
0
+2°C
1
-10°C
-50
+10°C
0
-10°C
-50
+10°C
0
60 min
0
30 min
0
60 min
0
90°C
0
1
0
2 min
0
70°C
-40
5°C
-40
+2°C
1
1
0
0
0
3 min
0
10 min/ore
1
60 min/ore
1
1
0
1
0
1
0
1
1
1
1
1
0
1
0
1
0
3
1
0
0
2
2
15
0
+50
0
+50
255
255
255
100
1
60
+99
+99
15
1
2
30
60
240
3
2
1
5
2
1
255
2
4
2
Publicidad
Capítulos
Tabla de contenido
