Publicidad
Idiomas disponibles
Idiomas disponibles
English
ing should be stored in a safe place for reuse if the product is
frequently used at different locations.
Beware of frost!
If drinking water is used as a coolant/lubri-
cant, the product must be protected against
frost during transport. If this is not possible,
the product must be drained and dried out!
3.3
Storage
Newly supplied products are prepared so that they can be
stored for at least 1 year. The product should be cleaned thor-
oughly before it is put into temporary storage!
The following should be taken into consideration for storage:
- Place the product on a firm surface and secure it against slip-
ping and falling over. Wastewater and sewage submersible
pumps are stored vertically.
Danger from falling over!
Never set down the product unsecured. If the
product falls over, injury can occur!
- Our products can be stored at temperatures down to
-15 °C. The store room must be dry. We recommend a frost-
protected room for storage with a temperature between 5 °C
and 25 °C.
Products that are filled with drinking water can only be
stored in frost-free rooms, at no less than 3 °C, for up
to 4 weeks. If longer storage is intended, the products
should be emptied and dried out beforehand.
- The product may not be stored in rooms where welding work
is conducted as the resulting gases and radiated heat can
damage the elastomer parts and coatings.
- Any suction or discharge ports should be closed tightly
before storage to prevent impurities.
- The current supply cables should be protected against kink-
ing, damage, and moisture.
Beware of electrical current!
Damaged power supply cables can cause
fatal
injury!
replaced by a qualified electrician immedi-
ately.
Beware of moisture!
Moisture penetrating the cable damages
both the product and cable. Therefore, never
immerse cable ends in the pumped liquid or
other liquids.
- The machine must be protected from direct sunlight, heat,
dust, and frost. Heat and frost can cause considerable dam-
age to propellers, rotors and coatings!
- The rotors or propellers must be rotated at regular intervals.
This prevents the bearing from locking, and the film of lubri-
cant on the mechanical shaft seal is renewed. This also pre-
vents the gear pinions (if present on the product) from locking
Defective
cables
must
and also renews the lubricating film on the gear pinions (pre-
venting rust film deposits).
Beware of sharp edges!
Sharp edges can form on rotors, propellers
and hydraulic openings. There is a risk of
injuries! Wear protective gloves.
- If the product has been stored for a long period of time it
should be cleaned of impurities such as dust and oil depos-
its before start-up. Rotors and propellers should be checked
for smooth operation. The housing coatings should be
checked for damage.
Before start-up, the filling levels (oil, motor filling, etc)
should be checked and topped up, if necessary. Prod-
ucts filled with drinking water should be completely
filled before start-up!
Damaged coatings should be repaired immediately.
Only a coating that is completely intact fulfills the crite-
ria for intended usage!
If these rules are observed, your product can be stored for a
longer period. Please remember that elastomer parts and coat-
ings become brittle over time. If the product is to be stored for
longer than 6 months, we recommend checking these parts
and replacing them as necessary. If this is the case, please con-
sult the manufacturer.
3.4
Returning to the product
Products that are returned to the factory must be properly
packaged. In this context, properly means that impurities have
been removed from the product and that it has been decon-
taminated, if it was used with fluids that are hazardous to
health. The packaging must protect the product from damage
during transportation. If you have any questions please contact
the manufacturer!
4
PRODUCT DESCRIPTION
The product has been manufactured with great care and is sub-
ject to constant quality controls. Trouble-free operation is guar-
anteed if it is installed and maintained correctly.
be
4.1
Proper use and fields of application
Manufacturer approval is required for pumping waste water
contaminated with chemicals.
Beware of electrical current
When using the product in swimming pools
or other accessible pools, there is a risk of
fatal injury due to electrical current. Note the
following information:
Use is strictly forbidden if there are people in
the pool.
If there are no people in the pool, protective
measures must be taken according to
DIN VDE 0100-702.46 (or the appropriate
national regulations).
The product is made from materials that are not KTW
approved. Furthermore, it can be used for pumping
waste water. Therefore, pumping drinking water is
strictly forbidden!
Proper use also includes observation of these instructions. Any
other use is regarded as improper.
33
Publicidad
