Publicidad
Idiomas disponibles
Idiomas disponibles
Right Soft Limit Position (Blink Code 1-1)
In this mode, Right, Left, Up and Down functions will be active . Move the monitor to the position that is to be set as the Right
Soft Limit. When in the desired position, press the Fog switch. The new Right Soft Limit is now set and the Left Soft Limit is
active for programming . Alternatively, activating the Stream command will abort this mode without storing the position and the
Left Soft Limit Position mode will be automatically selected .
Left Soft Limit Position (Blink Code 1-2)
In this mode, Right, Left, Up and Down functions will be active . Move the monitor to the position that is to be set as the Left
Soft Limit. When in the desired position, press the Fog switch. The new Left Soft Limit is now set and the Up Soft Limit is active
for programming . Alternatively, activating the Stream command will abort this mode without storing the position and the Up Soft
Limit Position mode will be automatically selected .
Up Soft Limit Position (Blink Code 1-3)
In this mode, Right, Left, Up and Down functions will be active . Move the monitor to the position that is to be set as the Up
Soft Limit. When in the desired position, press the Fog switch. The new Up Soft Limit is now set and the Down Soft Limit is
active for programming . Alternatively, activating the Stream command will abort this mode without storing the position and the
Down Soft Limit Position mode will be automatically selected .
Down Soft Limit Position (Blink Code 1-4)
In this mode, Right, Left, Up and Down functions will be active . Move the monitor to the position that is to be set as the Down
Soft Limit. When in the desired position, press the Fog switch. The new Down Soft Limit is now set and the Monitor Orientation
is active for programming . Alternatively, activating the Stream command will abort this mode without storing the position and
the Monitor Orientation mode will be automatically selected .
Monitor Orientation (Blink Code 1-7)
There are instances when it is desirable to mount the monitor other than in the factory default "flange on the bottom" position .
In those instances, this function prevents having to change the wiring of switches or re-programming CAN joysticks to handle
changes in Up/Down – Left/Right behavior . It is only necessary to program the monitor orientation when the monitor is
mounted on its side or upside down . When in this mode, determine which of the four inputs (Up, Down, Left, or Right) results
in "Up" movement . The last movement made prior to pressing the Fog switch will be used as the new "Up" motion and will remap
the other inputs accordingly . Move the monitor in whatever the current "Up" motion is and then press the Fog switch. The
new Monitor Orientation is now set and the Position Sensor "Zero" is active for programming. If the Stream switch is pressed
at any time before the Fog switch, the Monitor Orientation will remain unchanged and the Position Sensor "Zero" mode will be
automatically selected . NOTE: Use of this function will clear all stored obstacle avoidance profile data and require the
obstacle avoidance option to be reprogrammed.
Position Sensor "Zero" (Blink Code 1-8)
It is often difficult for the vehicle manufacturer to mount the monitor in the precise position where "straight ahead and level"
matches the calibration of the monitor at the Akron Brass factory . Use of this mode allows the user to "re-zero" the sensors at
the desired "straight ahead and level" position . First, use the Left/Right and Up/Down switches to position the monitor
"straight ahead and level". When the desired position has been reached, press the Fog switch. The new "zero" position is now
set and the Restore Factory Defaults mode is now active for programming. If the Stream switch is pressed at any time before
the Fog switch, the position sensor values will remain unchanged and the Restore Factory Defaults mode will be automatically
selected . NOTE: The soft limits positions, stow/deploy positions and CAN position reporting will be impacted by "re-zeroing".
If "re-zeroing" is needed, do so before setting soft limit, stow or deploy positions. NOTE: Use of this function will clear all
stored obstacle avoidance profile data.
Page 13
Publicidad
