Publicidad
Idiomas disponibles
Idiomas disponibles
Error Codes
Error codes are a two part blink code consisting of one or two short blinks, short pause, followed by a second set of blinks for the
specific code, then, a long pause . After the long pause, the code will repeat . During the pause between codes, the LED is on .
1-1 Rotation Sensor:
SWITCH: The rotation switch was not detected as part of a stow/deploy sequence .
POSITION FEEDBACK: The rotation position feedback sensor signal is missing or not changing while the monitor is moving .
1-2 Elevation Sensor:
SWITCH: The elevation switch was not detected as part of a stow/deploy sequence .
POSITION FEEDBACK: The elevation position feedback sensor signal is missing or not changing while the monitor is moving .
1-3 Swing Arm Sensor error:
3440 DeckMaster only: The swing arm hit a hard stop instead of stopping on the sensor
1-4 Attitude Sensor error:
3351 Tuckaway with autolevel only
1-5 Operator Override:
During a Stow/Deploy sequence, a command input was received which interrupted the sequence (emergency stop) or an ob
stacle was hit causing the monitor to stop before completing the sequence .
1-6 Obstacle Avoidance Profile Needed:
The obstacle avoidance feature was turned on, but an avoidance profile was not learned .
1-7 Rotation Hard Stop:
(position feedback units only) A hard stop was encountered during normal rotation . This is an unexpected condition and
could be a sensor problem or an obstruction was hit .
1-8 Elevation Hard Stop
(position feedback units only) A hard stop was encountered during normal elevation . This is an unexpected condition and
could be a sensor problem or an obstruction was hit .
1-9 Swing Arm Hard Stop
3440 DeckMaster Only . The Swing Arm hit an obstruction between stow and deploy positions .
2-1 Electric Riser:
Electric riser function is turned on but the riser is not available on the network .
Maintenance Instructions
• The monitor should be kept clean and free from dirt .
• Inspect for damaged components or wiring and repair or replace as needed .
• The monitor should move freely and smoothly without hesitating .
• Inspect monitor for leaks . Replace seals as needed . Use Parker O-Ring lubricant on O-Rings .
• Grease fittings are installed at worm gear and ball bearing joints . If motor is laboring or movement of the joint is not smooth,
grease until normal operation is restored . Do not over-apply grease using a grease gun . Pressure will build in the monitor cavity
and could cause damage to the monitor . The elevation joint bearings do not require grease .
Warranty Statement
WARRANTY AND DISCLAIMER*: We warrant Akron Brass products for a period of five (5) years* after purchase against defects
in materials or workmanship . Akron Brass will repair or replace product which fails to satisfy this warranty . Repair or replace
ment shall be at the discretion of Akron Brass . Products must be promptly returned to Akron Brass for warranty service . We will
not be responsible for: wear and tear; any improper installation, use, maintenance or storage; negligence of the owner or user;
repair or modification after delivery; failure to follow our instructions or recommendations; or anything else beyond our control .
WE MAKE NO WARRANTIES, EXPRESS OR IMPLIED, OTHER THAN THOSE INCLUDED IN THIS WARRANTY STATEMENT, AND WE
DISCLAIM ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE . Further, we will not
be responsible for any consequential, incidental or indirect damages (including, but not limited to, any loss of profits) from any
cause whatsoever . No person has authority to change this warranty . Unless otherwise provided herein, Akron Brass industrial
electronic components & the Severe-Duty Monitor have a one (1) year warranty . Select Akron Brass handline nozzles and valves
carry a ten (10) year warranty . Weldon products have a two (2) year warranty from date of manufacture (excluding consumable
components) . Select Weldon LED products carry a five (5) year warranty . Honda products have the manufacturers' warranty and
Akron Brass disclaims any warranty with respect to those products .
ISO 9001 REGISTERED COMPANY
PHONE: 330 . 2 64 . 5 678 or 800 . 2 28 . 1 161 I FAX: 330 . 2 64 . 2 944 or 800 . 5 31 . 7 335 I www . a kronbrass . c om
WARRANTY AND DISCLAIMER: We warrant Akron Brass products for a period of five (5) years after purchase against defects in materials or workmanship . Akron Brass will repair or replace
product which fails to satisfy this warranty . Repair or replacement shall be at the discretion of Akron Brass . Products must be promptly returned to Akron Brass for warranty service .
We will not be responsible for: wear and tear; any improper installation, use, maintenance or storage; negligence of the owner or user; repair or modification after delivery; damage; failure to
follow our instructions or recommendations; or anything else beyond our control . WE MAKE NO WARRANTIES, EXPRESS OR IMPLIED, OTHER THAN THOSE INCLUDED IN THIS WARRANTY
STATEMENT, AND WE DISCLAIM ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE . Further, we will not be responsible for any consequential,
incidental or indirect damages (including, but not limited to, any loss of profits) from any cause whatsoever . No person has authority to change this warranty .
© Premier Farnell Corporation . 2000 All rights reserved . No portion of this can be
reproduced without the express written consent of Premier Farnell Corporation .
REVISED: 9/13
Publicidad
