Normal Or Angle Style Fan Mounting; Wiring - Harbor Breeze POINT BREAK Manual Del Usuario

NORMAL OR ANGLE STYLE FAN MOUNTING

1. Choose downrod (A) length you wish to use.* If you choose to use
the 12 in. downrod (A), remove hanging ball from the 6 in. downrod (A)
and attach to the 12 in. downrod (A). Insert downrod (A) through canopy
(B) and yoke cover (F). Thread wires from motor housing (E) through
downrod (A). [Fig. 1]
*Helpful Hint: Downrod style mounting is best suited for ceilings 8 ft.
(2.44 m) high or higher. For taller ceilings you may want to use a longer
downrod (not included) than the ones provided. Angle style mounting is
best suited for angled or vaulted ceilings. Longer downrods are
sometimes necessary to ensure proper blade clearance.
2. Remove pin (S) and clip (T) from motor housing yoke. Slip downrod
(A) into motor housing yoke, align holes and re-install pin (S) and clip
(T). Tighten downrod set screws and then tighten nuts. Slide yoke cover
(F) down until it rests on top of motor housing (E). [Fig. 2]
3. Install ball end of downrod (A) into mounting bracket (C) opening.
Align slot in ball with tab in mounting bracket (C). [Fig. 3]
Warning: Failure to align slot in ball with tab in mounting bracket
(C) may result in serious injury or death.
WIRING (continued on next page)
WARNING: To reduce the risk of fire, electrical shock, or
personal injury, wire connectors provided with this fan are designed
to accept only one 12 gauge house wire and two lead wires from
the fan. If your house wire is larger than 12 gauge or there is more
than one house wire to connect to the two fan lead wires, consult
an electrician for the proper size wire connectors to use.
Important: Be sure wiring box is properly grounded or that a
ground (green or bare) wire is present.
Warning: If house wires are different colors than referred to
in following steps, stop immediately. A professional electrician is
recommended to determine wiring.
1. Choose wiring diagram [Fig. 1A, Fig. 1B or Fig. 1C] that fits your
situation and make appropriate wiring connections as follows: (Make
special note of Step 3 on the following page while wiring.)
1A. Connect BLACK and BLUE wire from fan to BLACK wire
from ceiling with wire connector (P) provided. Connect WHITE
wire from fan to WHITE wire from ceiling with wire connector (P)
provided. Connect all GROUND (GREEN) wires together from fan
to BARE/GREEN wire from ceiling with wire connector (P)
provided. [Fig. 1A]
1B. If you intend to control the fan light with a separate wall
switch, wire as indicated in the instructions in 1A except connect
BLUE wire from fan to the BLACK supply from the independent
switch. [Fig. 1B]
1C. If you intend to control the fan and light with separate wall
switches, wire as indicated in the instructions in 1A except
connect BLUE wire from fan to the BLACK supply from the
independent wall switch for the light and connect BLACK wire
from fan to the BLACK supply from the other independent wall
switch for the fan. [Fig. 1C]
Note: Black wire is hot power for fan. Blue wire is hot power for
light kit. White wire is common for fan and light kit. Green or bare
wire is ground.
FAN AND LIGHT CONTROLLED BY CHAIN.
Fig. 1A
BLACK (POWER)
WHITE (NEUTRAL)
FAN CONTROLLED BY CHAIN, LIGHT BY WALL SWITCH.
Fig. 1B
BLACK (POWER)
SWITCHED LIGHT POWER
WHITE (NEUTRAL)
FAN AND LIGHT CONTROLLED BY SEPARATE WALL SWITCHES.
Fig. 1C
SWITCHED FAN POWER
SWITCHED LIGHT POWER
WHITE (NEUTRAL)
6
Hanging
Ball
B
A
F
Fig. 1
F
A
T
S
Fig. 2
C
A
B
Fig. 3
GROUND
GROUND
BLACK
WHITE
BLUE
GROUND
GROUND
WHITE
GROUND
GROUND
WHITE
Set
Screw
E
Ball
BLUE
BLACK
BLUE
BLACK