Setting The Saddle - Moustache Lundi 27 Manual De Usario

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 86

3.2 SETTING THE SADDLE

We have equipped our bikes with ergonomic saddles, but a careful set up is required to ensure
optimal comfort. In this section you will find advice for an angle and set back of your saddle,
that's adjusted to the type of riding you do. Then, you will find the process to follow to correctly
set up your saddle depending on the type of seat post your Moustache has. Finally, at the end
of this section, you will find advice and settings for suspension and telescopic seat posts.
3.2.1 Advice
It is generally advised to position the saddle horizontally for a mixed usage. On the Lundi 27
models, the torso position is straighter and the pelvis lightly tilted backwards. We advise you
to set the saddle slightly inclined towards the back, in order to optimize your comfort and the
riding position. For an all-terrain use, it is advised to set the saddle slightly inclined towards
the front (Figure 5 ).
The saddle set back should be adjusted for the length of the femur. This is a more complex
setting which may require the help of your retailer. In general an intermediate setback is
adequate. Its setting should be carried out during the setting of saddle angle. Respect the
level of torque advised for the screw of the saddle chassis. This will be indicated on it and varies
from one model to another.
Figure 5. Saddle angle settings for Monday 26 (left), mixed use (middle) and MTB use (right)
A new saddle can cause slight discomfort that will diminish with
time. If you do not find the right position, ask your retailer for
advice.
3.2.2 Setting the angle and setback of your saddle
Firstly, you need to check the seat post that is on your Moustache.
This is very easy: you simply need to check the number of screws
that attach your saddle chassis to the seat post.
There are two possibilities: there is only one screw as in
Figure 6, in this case go to the section Only one fitting block.
If you see that there are two screws, go to the section Two fitting
blocks as in Figure 7.
56
Figure 6. Saddle with one fitting block
Figure 7. Saddle with two fitting
blocks
ONLY ONE FITTING BOLT:
If you have only found one fitting block, you are in the right section. To adjust the angle of your
saddle you need to carry out the following process:
1. Loosen the screw that holds the saddle
and seat post using a 6mm allen key
as in Figure 8 to obtain enough play to
easily move the saddle.
2. Adjust the angle and setback of the
saddle as suits you.
3. Tighten the screw, ensuring that it does
not surpass the maximum torque level
indicated next to the screw.
4. Contrôlez si la selle est bien maintenue
et ne présente pas de jeu.
TWO FITTING BOLTS:
If you have found two fitting blocks, you are in the right section. To adjust the angle of your
saddle you need to carry out the following process:
1. Loosen the two screws that hold the saddle and seat post using a 5mm allen key
(Figure 9) until the saddle can move easily.
2. Adjust the angle and setback of the saddle as suits you.
3. Tighten each screw a half-turn, alternating between the two, without going over the
maximum torque level that is indicated next to them.
4. Check that the saddle is correctly in place and that there is no play.
Figure 9. Steps for tightening/loosening the fitting blocks
3.2.3 Special cases
You can't find the right explanation for your bike? You can check the Moustache technical
notice available on our website www.moustachebikes.com/en/manuals, to obtain detailed
information on your model.
FR
EN
DE
IT
ES
NL
Figure 8. Tightening/loosening the fitting block
57

Publicidad

Tabla de contenido
loading

Tabla de contenido