Stiga MPST 84 Li 48 V1/V2 Manual De Instrucciones página 297

hole and turning it so that both the spring
(fig. 6.B) and the terminal (fig. 6.B.2) are
securely positioned in their housings.
2. Position the side discharge chute (fig.
6.A) in line with the cutting means
assembly brackets (fig. 6.C). Using a
screwdriver, turn the second terminal
(fig. 6.B.2) of the spring (fig. 6.B) to bring
it outside the side discharge chute.
3. Fit the pin (fig. 6.D) in the holes on the
brackets (fig. 6.C) and on the side discharge
chute, so that it passes through the coils
of the spring (fig. 6.B) and the drilled end
comes out of the inner most bracket.
4. Insert the cotter pin (fig. 6.E) into the hole
(fig. 6.D.1) on the pin (fig. 6.D) and rotate
the pin in order to bend the two ends (fig.
6.E.1) of the cotter pin, (with the aid of a
pair of pliers), so that it cannot slide out,
causing the pin (fig. 6.D) to disengage.
WARNING
Check that the spring works correctly and keep
the side discharge chute securely lowered. Make
sure that the pin is fitted properly to prevent
it from falling out accidentally. make sure that
the side discharge guard (Fig. 7.A) is lowered
and locked with the safety lever (Fig. 7.B).
ATTENTION
Before disassembling or servicing the
deflector, always push the safety lever
(Fig. 8.B) and lift the side unloading
guard (Fig. 8.A) to allow disassembly.
NOTE
To remove the deflector, perform
assembly steps in reverse order.
5.6 FITTING OF THE SIDE
REINFORCEMENTS OF THE
CUTTING MEANS ASSEMBLY
(FOR MODELS WITH SIDE
DISCHARGE ONLY, IF AVAILABLE)
Finish the fitting cutting means assembly
mounting the side reinforcements on the
profile of the cutting means assembly
using the relative screws (fig. 9)
5.7 MOUNTING AND COMPLETING
OF THE REAR PLATE (ONLY
FOR MODELS WITH REAR
GRASS CATCHER)
1. Fit the two lower brackets (fig.10.A)
and (fig.10.B), respecting the assembly
direction indicated in the figure, fix
them with the screws (fig.10.C) and
nuts (fig.10.D) , tightening them fully.
2. Remove the two screws (fig.
10.H), which will be used later.
3. Fit the lower part (fig. 10.E) of the rear
plate and fix it to the lower brackets with
the screws (fig. 10.F) and nuts (fig. 10.G),
without tightening them completely.
4. Complete the fastening of the lower
part (fig.10.E) of the rear plate by
fully tightening the two central screws
(fig.10.H) previously removed and
the four upper screws (fig.10.I)
5. Fully tighten the two lower nuts (fig. 10.G).
6. Insert the lever (fig. 10.J) of the
full collection bag indicator in
its seat (fig. 10.K) and push it
down until a click is heard.
7. Fit the two supports of the grass catcher
(fig.10.L) and (fig.10.M), respecting
the assembly sequence indicated
in the figure, and fix them with the
screws (fig.10N) and spring washers
( fig. 10.O), tightening them fully.
5.8 MOUNTING OF THE GRASS
CATCHER (ONLY FOR MODELS
WITH REAR GRASS CATCHER)
(ONLY FOR MODELS OF TYPE "III")
1. Use the grass catcher open / close
buttons (fig. 13.U, V) to align the two-
cam lever (fig. 11.A) with the supports
(fig. 11.B) of the grass catcher.
NOTE
To carry out the alignment, and then
manually adjust the position of the two-
cam lever (fig.11.A), it is necessary to keep
the opening (fig.13U) or closing (fig.13V)
button of the grass catcher pressed.
2. Hook the grass catcher (fig. 16.A) to the
supports (fig. 16.B) and centre it with respect
to the rear plate. Centring is ensured by
using the right support as a lateral support.
EN - 11