Publicidad
Idiomas disponibles
Idiomas disponibles
Adjusting the Set Temperature
When using a panel with Up and Down buttons (Temperature buttons), pressing Up or Down will cause the temperature to fl ash. Pressing a tempe-
rature button again will adjust the set temperature in the direction indicated on the button. When the LCD stops fl ashing, the spa will heat to the new
set temperature when required.
Press and hold
If a temperature button is pressed and held when the temperature is fl ashing, the temperature will continue to change
until the button is released. If there is only one temperature button it will change until the limit of the temperature range is reached and if the button
is held down, the progression will reverse the direction.
Dual Temperature Ranges
For example
High range 80˚F and 104˚F (26.7˚C to 40˚C).
Low range 50˚F and 99˚F (10˚C to 37.2˚C)
More specific ranges must be programmed by the provider.
The antifreeze protection must be active in all ranges.
Main Screen
High-Range vs.
Low-Range Temp Choice
To next item in Main Menu
Main Screen
Setting the set temperature
In order for the spa to heat, a pump needs to circulate water through the heater.
Ready mode (indicated by
) will circulate the water every half hour using up the heater as necessary and taking a new temperature reading.
Sleep mode (indicated by
) will only circulate and heat the water only during fi lter cycles.
Main Screen
Menu/Select
Press
repeatedly until MODE
appears in the LCD.
To next item in
Main Menu
If not toggled
Main Screen
Modo listo en modo reposo
/
will appear on the display when the spe is in REST and the button is pressed
perature. After 1 hour, the system will return to the REST state. This mode can also be reset by entering the mode menu and changing the mode.
temperature and temp range
Set Temp will Show & Flash
Press a Temp Button repeatedly to change the temperature.
Pressing and holding a Temp Button will also change the temperature.
Toggle the Range arrows in the LCD.
To Set
*****
Waiting a few
seconds reverts to
original settings
Set Temp will Show & Flash
Press a Temp Button repeatedly to change the temperature.
Pressing and holding a Temp Button will also change the temperature.
mode – ready and Rest
Main Screen
To Set
*****
Waiting a few
seconds reverts to
original settings
Toggle between Ready (indicated by
) and Rest (indicated by
Menu/Select
Pressing
when the display is toggled will go to Main Screen.
Ready Mode will allow the spa to Poll and determine a need for heat. The panel will maintain a "current" temperature display.
Rest Mode will not Poll and will only heat during filter cycles. The panel will not display a current temperature at all times.
1 Hour
The Main Screen will display RUN PUMP FOR TEMP if the primary pump has not run for over 1 hour.
The Main Screen will display normally during Filter Cycles or when the spa is in use.
If the primary pump has been off for an hour or more, when any function button, EXCEPT Light, is pressed on the panel,
the pump used in conjuncton with the heater will run so that temperature can be sensed and displayed.
Pantalla principal
Presionar botón "Jets"
Key
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for "Action" (
Menu/Select button
Waiting time that keeps the last change to a menu item.
*****
Waiting time (depends on menu item) that reverts to original setting and
ignores any change to that menu item.
Main Screen
OR
a few seconds
Main Screen
Main Screen
OR
a few seconds
Key
Indicates Flashing or Changing Segment
Indicates Alternating or Progressive Message - every 1/2 second
A temperature button, used for "Action" (
Menu/Select button
Waiting time that keeps the last change to a menu item.
Waiting time (depends on menu item) that reverts to original setting and
*****
ignores any change to that menu item.
).
. The spa is supposed to be used and heated to the set tem-
Pantalla principal
)
)
15
Publicidad
