Profi Cook PC-ES 1265 Manual De Instrucciones página 17

3. Insert the filter holder.
4. Switch on the appliance. A beep sounds. The indicator
light of the button lights up while the two indicator
lights of the cups flash. The appliance starts heating.
The heating plate becomes hot.
5. Swivel the steam pipe outwards. Make sure that the
steam nozzle is turned up.
6. Place a suitable container (heat-resistant / approx. 500 ml)
under the steam nozzle.
7. Press the button for steam.
8.
WARNING: Risk of Burns!
Hot steam comes out of the steam nozzle.
To produce steam, set the controller to position . When
a steady stream of water comes out of the steam nozzle,
switch off the pump. Set the controller to position
WARNING: Risk of Burns!
• When moving the steam nozzle after steaming,
always grasp it by the black rubber handle!
• The water in the vessel is hot.
9. Empty the receptacle and place it under the brew head.
To do this, remove the collection container for the resid-
ual water if necessary.
10. Make sure the controller is in position .
11. Press the button for the steam again. As soon as
both control lights for the buttons light up, start the pump
with the button. A water flow starts. Let 2 – 3 cups run
through. To empty the vessel in the meantime, switch off
the pump. To do this, press the
WARNING: Risk of Burns!
The water in the vessel is hot.
12. The appliance is now vented and ready for operation.
Program Individual Coffee Quantity
You have the option of changing the factory-set coffee
quantity. Two standard quantities for one cup ( ) and
for two cups ( ) are set at the factory. To change these
according to your wishes, proceed as follows:
1. Fill the water tank with sufficient water and reinsert it.
2. Fit the filter holder without the coffee grounds.
3. Place a cup under the brew head.
4. Insert the mains plug into a socket and switch on the
appliance.
5. Wait until the two indicator lights of the cups light up.
Then press and hold the button whose standard quantity
is to be set.
6. Once the desired quantity is reached, release the button.
- A beep sounds and the indicator lights flash to display
that the programming has been successfully saved.
The appliance is now ready for use again.
PC-ES1265_IM
Delete Programmed Coffee Quantity
Proceed as follows to delete the individually programmed
coffee quantity and restore the standard quantity:
1. Fill the water tank with sufficient water and reinsert it.
2. Fit the filter holder without the coffee grounds.
3. Place a cup under the brew head.
4. Insert the mains plug into a socket, but do not switch on
the appliance.
5. Press and hold both buttons (
Then press and hold the
- To display that the programming has been deleted,
6. After the reset, the appliance switches off.
Press the
only stop when the
(off).
7. Press one of the two buttons. Some water comes out of
the brew head, then the beeping stops.
8. The two indicator lights flash. Then two beeps are heard
and the indicator lights light up. The appliance is now
ready for use again.
Insert and Remove Filter Inserts
• There are guide lugs on the filter inserts. These must be
inserted into the notch of the filter holder. Then turn the
filter insert by 90 degrees so that it does not fall out when
emptying later.
• To be able to remove the filter insert, it must be turned in
such a way that the guide nose is again in the notch of
the filter holder. Now the filter insert can be removed.
button.
Espresso Preparation
1. Fill the water tank with sufficient water and reinsert it.
The water level must be between the MIN and MAX
marks.
2. Switch on the appliance. A beep sounds. The indicator
light of the
lights of the cups flash. The appliance starts heating.
The heating plate becomes hot.
3. If you have previously frothed milk, release all pressure
from the appliance:
3.1 When the indicator light of the
3.2 Place a suitable vessel under the steam nozzle.
3.3 Set the controller to position until no more steam
3.4 Turn the controller back to position .
4. Select a filter insert (11 / 12). Place it in the filter holder.
Make sure that the filter insert is turned 90 degrees so
that it does not fall out when emptying later. See previ-
ous chapter "Insert and Remove Filter Inserts".
5. Fill the filter insert with espresso grounds. Use the
measuring spoon provided (one measuring spoonful =
1 cup). Distribute the coffee grounds evenly and press
/
button in addition.
5 beeps sound.
button. The appliance emits beeps. These
or button is pressed.
button lights up while the two indicator
press this button to switch off the function. Also
make sure that the controller is set to .
comes.
) simultaneously.
button is on,
17
09.11.23