Grillo G110 Manual De Instrucciones página 16

Translation of the Original Instructions
SNOW THROWER
This implement (fig. 14) has been especially designed for this particular rotovator. It is very useful
for clearing snow from yards, driveways, etc. It consists of a turbine rotary unit enclosed in a
special case open at the front, which rotates at high speed, collecting the snow and throwing it
along a pipe. The pipe angle can be adjusted to throw the snow in any direction to a distance of 8 –
10 metres. The snow thrower is fixed to the implement flange using two nuts. The handlebar must
be turned through 180towards the engine and follow the directions given for the mower bar. To
operate the snow thrower the safety device must be positioned as shown (fig. 2A).
Important: when reconnecting the rotary tiller, the safety device must be set in the original
position. We do not accept any responsibility for failure to follow this rule (fig. 2).
The snow thrower is 70 cm wide and can clear snow up to 40 cm deep. Wheel weights should be
used for best performance. If the snow is very wet, keep the ejection pipe turned forward to avoid
obstructions at the outlet. The two side skids must be adjusted so that they just skim level ground
(asphalted streets) or keep the snow thrower high if the ground is uneven. Maintenance: when
work is over, remove any snow left in the snow thrower so it cannot freeze and block the turbine.
Do not clean the attachment when the engine is running. Attention, danger! Do not touch
the snow thrower while it is working.
ATTENTION: While attaching the different implements to the flange, make sure that the two parts
are perfectly aligned. The nuts of the two stud-bolts must be screwed on by hand and then using a
wrench so that they apply pressure to the flange simultaneously.
PLOUGHS
The ploughs designed for this rotavator have been especially developed to obtain good ploughing
without overstraining the operator. The models available are a single-share plough and an
180roll-over plough. The latter is especially suitable when working backwards and forwards, such
as along rows of vines or fruit-trees. The depth of the furrow obtained may vary from 10 to 15 cm
depending on the terrain. Users can achieve excellent performances using the tyres 5.00-12 and
possibly the wheel-weights, which improve machine's adhesion.
ROTARY CUTTER
The rotary blade cutter 75cm for the rotovator (fig. 16) is designed for the maintenance of grounds
with too high grass. The high power available, the driving wheels, the working speeds and the
reverse gear allow operation in the most difficult conditions without tiring the operator and with
considerable time saving. The rotary cutter is fixed to the implement flange using two nuts. It is
supplied with the lateral rams for hard conditions, or with front support wheels in order to use it with
low grass and levelled soils. The handlebar must be turned through 180towards the engine and
then follow the directions given for the mower bar. To operate the rotary cutter the safety device
must be positioned as shown (fig. 2A). Important: when reconnecting the rotary tiller, the safety
device must be set in the original position. We do not accept any responsibility for failure to
follow this rule (fig. 2). The blade is driven by means of a bevel gear pair and is equipped with a
release mechanism and a brake blade so that its force of inertia cannot drag the machine forward
when the clutch is engaged. To adjust the cutting height vary the position of the rotary cutter wheel,
or of the lateral rams.
Maintenance: Keep the lawn mower blade well sharpened: the cut will be better and the engine
will not strain. Always tighten the two fixing bolts well when fastening or removing the blade. Check
the two nuts fixing the awn mower to the machine frequently. Check the gearbox oil level every 50
hours, removing the cap on the top, and make sure that the oil level is within 50mms of the hole; if
the level is lower add 80W/90 (API GL5 US-MIL-L-2105D) gearbox oil. Change the oil once a year.
Attention! Rotating blades are very dangerous, never put hands or feet under the rotary
cutter. Do not clean the attachment when the engine is running.
14