Removing The Batteries:; Inserting The Batteries; Charging Battery Handles With Rechargeable Batteries - Riester ri-scope Instrucciones Para El Uso

- Unscrew the battery handle cover on the lower part of the handle in a coun-
ter clockwise direction.
- Insert the standard alkaline batteries designated for this battery handle with
the plus side in the direction of the handle top into the battery handle.
- Screw the battery handle cover firmly back onto the battery handle.

3.2. Removing the batteries:

Battery handles (2.3 and 2.7) type C and AA with rheotronic
- Unscrew the battery handle cover on the lower part of the battery handle in
a counter clockwise direction.
- Remove the batteries from the battery handle by holding the opening of the
battery handle slightly downwards and shaking it slightly if necessary.
- Screw the battery handle cover firmly back onto the battery handle.
ATTENTION!
For all factory-installed or separately supplied batteries, the red safety foil on
the plus side must be removed before startup!
ATTENTION!
Only applies to battery handle (2.5) type C with rheotronic
in the 230 V or 120 V socket:
When using the new ri-accu® L art. no. 10692, make sure that there is no insu-
lation on the spring of the battery grip cover. When using the old ri-accu® L art.
no. 10692, insulation must be attached to the spring (danger of short circuit!).
neuer ri-accu L
®

3.3. Inserting the batteries:

Battery handles (2.4 and 2.8) type C and AA with rheotronic
ger® L).
Battery handle type C with rheotronic
Battery handle (2.5) type C with rheotronic
230 V or 120 V.
ATTENTION!
Please observe safety instructions!
- Unscrew the battery handle cover on the lower part of the handle in a coun-
ter clockwise direction.
- Remove the red safety foil on the plus side of the battery during initial star-
tup.
- Insert the battery approved for your battery handle (see 2.2) into the battery
handle with the plus side in the direction of the handle top. In addition to the
plus sign you will also find an arrow that shows you the direction of insertion
into the battery handle.
- Screw the battery handle cover firmly back onto the battery handle.
3.4. Removing the batteries:
Battery handles (2.4 and 2.8) type C and AA with rheotronic
ger® L).
Battery handle type C with rheotronic
Battery handle (2.5) type C with rheotronic
230 V or 120 V.
ATTENTION!
Please observe safety instructions!
- Unscrew the battery handle cover on the lower part of the battery handle in
a counter clockwise direction.
- Remove the batteries from the battery handle by holding the opening of the
battery handle slightly downwards and shaking it slightly if necessary.
- Screw the battery handle cover firmly back onto the battery handle.
4. Charging the battery handles with rechargeable batteries:
4.1. Battery handles (2.4 and 2.8) type C and AA with rheotronic
ri-charger® L).
- Can only be used in the charger ri-charger® L (art. no. 10705, art. no. 10706)
from Riester.
- The ri-charger® L charger comes with an additional user manual that must
be observed.
4.2. Battery handle type C with rheotronic
- It can only be used with the plug-in charger (art. no. 10707) from Riester..
For this purpose, the small round plug is inserted into the lower part of the
battery handle through the opening in the battery handle cover in the battery
(art. no. 10694 ri-accu® L).
Now connect the mains plug of the plug-in charger to the power supply. The
charge status of the battery is indicated via the LED on the plug-in charger.
Red light means charging, green light means that the battery is fully charged.
20
alter ri-accu L
®
3.5 V (for plug-in charger)
®
3.5 V for charging in the socket
®
3.5 V (for plug-in charger)
®
3.5 V for charging in the socket
®
3.5 V (for plug-in charger)
®
2.5 V:
®
3.5 V for charging
®
3.5 V (for ri-char-
®
3.5 V (for ri-char-
®
3.5 V (for
®