Ingersoll Rand G330 Guía De Usuario Y Mantenimiento Manual página 43

! In this operating mode, any event appearance (alarm, fault, external command, ...) is signalled on screen. However, the generating set is
stopped and automatic start-up is not possible.
Ph./ph. U12
3 3 9 9 6 6
voltages U23
3 3 9 9 0 0
(Volts) U31
3 3 9 9 5 5
STOP mode selected
2.2. M M anu M M ode
! The Manu mode provides local control from the keyboard, ie, the operator is wholly in control of the start procedure.
-This mode may be accessed from the Stop or Auto modes.
The generator starts in Manu mode after a single press on the Start key. Using this function:
- The red LED usually associated with the Start key does not flash,
- The message confirming the selection of Manu mode does not appear.
2.3. A A uto M M ode
Auto mode can be accessed from Stop, Manu or Test mode. Press the Auto button to select the mode and to display the left-hand side screen
below for two seconds. The red LED associated with the button comes on, then the right-hand screen appears. This screen corresponds to
the standby state of the generating set.
Fuel Lev(%)
E.Speed(RPM)
2 2 4 4
Batt. (Volts)
AUTO mode selected
! From the waiting screen, the generating set start-up is conditioned by:
$ Logical status change of the 'external command' input
% Logical status change of the 'EJP advance warning' or 'EJP start-up' inputs (France only)
& Activation of the clock mode built into (if the mode is programmed).
Example: the right-hand side screen above informs of the logical status of the external start-up command (abbreviation ext command=0 or
ext command=1):
- External command = 0, no start-up
- External command = 1, imminent start-up possible
! When one of the three start-up conditions changes from 0 to 1 (for $ and %) or from inactive to active (for &), a new message informs
the operator, then the generating set enters into an automatic start-up phase.
! When one of the three start-up conditions changes from 1 to 0 (for $ and %) or from active to inactive (for &), a new message informs
the operator, then the generating set enters into an automatic shutdown phase.
! In Auto mode, the ATS toggle is completely automatic.
2.4. T T est M M ode
Test mode can only be accessed from Auto mode. If one of the inputs ; external command, EJP advance warning, EJP start-up, is in logical
status 1 or if the clock is active, Test mode cannot be selected.
! If the inputs; external command, EJP advance warning, EJP start-up, are in logical status 0 or if the clock is inactive, press Auto Test but-
ton to select the mode and to bring up the screen below. The red LED associated with the button flashes.
Fuel Lev(%)
E.Speed(RPM)
2 2 4 4
Batt. (Volts)
TEST mode selected
press Auto Test to confirm
! If you do not press Auto Test to confirm, Auto mode is automatically selected after two minutes.
! In Test mode, the ATS cannot be toggled, this is a no-load operation. The generating set operating time is indicated on screen by a time
displayed in minutes and seconds which counts down automatically. When the delay elapses, the generating set shuts down without cooling
and automatically goes into Auto mode.
! When the generating set is running and whatever the current mode (Auto, T T est, M M anu), press the Stop
button to stop it instantly without any cooling down. A message appears on screen for two seconds
to signal that the button has been taken into account (see screen opposite).
Note: if the engine is equipped with a water heater, the latter is not powered in Stop mode.
5 5 0 0
Fuel Lev(%)
0 0
E.Speed(RPM)
2 2
Batt. (Volts)
.
ext command=0
gen stand-by
! Press Auto Test button again to confirm the mode, the associated red LED comes on continuously
5 5 0 0
and the generating set then enters into an automatic start-up phase.
! When the red LED flashes (waiting for confirmation), the mode can be changed by selecting Stop
0 0
mode or Auto mode.
2 2
.
5 5 0 0
0 0
2 2 4 4 2 2
.
16:50
12/01/00
13